Qashqai J11. Door & Lock — part 32
PREPARATION
DLK-513
< PREPARATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000010435118
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
DLK-514
< SYSTEM DESCRIPTION >
[TYPE 4]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010435119
Component Description
INFOID:0000000010435120
1.
Power window main switch
(door lock/unlock switch)
2.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Combination meter
4.
Front power window switch (passen-
ger side) (door lock and unlock
switch)
5.
Door lock assembly
6.
Door switch
7.
Back door lock assembly
8.
Back door opener switch
JMKIB3273ZZ
Item
Function
Back door lock assembly
Opens the back door with the back door open signal from BCM.
BCM
BCM detects the vehicle status according to signals from each door switch and
each outside/inside key antenna. BCM transmits drive signal to door lock actuator
when BCM receives operation signal from remote keyless entry receiver and each
switch.
Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
for de-
tailed installation location.
Combination meter
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door lock and unlock switch
Transmits door lock/unlock operation to BCM.
Door switch
Detects door open/close condition.
Keyfob
Transmits button operation to remote keyless entry receiver.
Key switch
Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.
POWER DOOR LOCK SYSTEM
DLK-515
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
POWER DOOR LOCK SYSTEM
System Diagram
INFOID:0000000010435121
System Description
INFOID:0000000010435122
DOOR LOCK FUNCTION
Door Lock and Unlock Switch
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is built into front power window switch (passenger side).
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors actu-
ator are unlocked.
Unlock Sensor
• BCM locks all doors or unlocks all doors, when driver door lock knob is operated.
• With the mechanical key inserted in the door key cylinder on driver side, turning it to lock position, locks door
lock actuator of all doors.
• With the mechanical key inserted in the door key cylinder on driver side, turning it to unlock position, unlocks
door lock actuator of all doors.
Operation Condition
If all of the following conditions are satisfied, door lock and unlock operation is performed using the door lock
and unlock switch.
*
1
: While door lock and unlock switch is pressed in the lock direction during this state, combination meter buzzer sounds and warns.
*
2
: When this item becomes OK according to keyfob ID verification, door lock/unlock operation is allowed.
KEY REMINDER FUNCTION
• While ignition key is inserted in ignition key cylinder and driver door is open, door is not locked when door
lock and unlock switch is pressed in the lock direction. This prevents keyfob from being left in the vehicle.
• While door lock and unlock switch is pressed in the lock direction, combination meter buzzer sounds and
warns.
DOOR LOCK STATUS INDICATOR OPERATION
JMKIB2483GB
Door lock and unlock switch operation
Operation condition
LOCK
• Ignition Key is removed from ignition key cylinder and closed driver
side door*
1
• Doors other than drivers door are closed*
1
• Door are not locked by keyfob*
2
• Door lock that is requested is not auto door lock*
2
UNLOCK
Door are not locked by keyfob*
2
DLK-516
< SYSTEM DESCRIPTION >
[TYPE 4]
POWER DOOR LOCK SYSTEM
The door lock status indicator indicates door lock status under the following condition.
UNLOCK LINK FUNCTION
When driver door or passenger door is opened using the override function, all doors are unlocked.
Unlock function operates when driver door or passenger door is open while all of the following conditions are
satisfied.
NOTE:
When anti-hijack function is activated, only the applicable door is unlocked.
Indicator operation
Ignition position
Door status
Lock operation
ON (30 minutes timer)
OFF
All doors are closed and door
is locked
Door lock and unlock switch
ON
ON
All doors are closed and door
is locked
Door lock and unlock switch
ON (1 minute timer)
OFF
All doors are closed and door
is locked
Keyfob or auto door lock func-
tion
ON
ON
All doors are closed and door
is locked
Keyfob or auto door lock func-
tion
ON
→
OFF
–
(All doors are closed
→
any
door is open) or (All doors are
locked
→
any door is un-
locked)
–
ON (timer is running)
→
ON
(timer is stop)
OFF
→
ON
–
–
ON
→
ON (30 minutes timer)
ON
→
OFF
–
Door lock and unlock switch
ON
→
ON (1 minute timer)
ON
→
OFF
–
Keyfob or auto door lock func-
tion
Operation condition
• Doors are locked by door lock/unlock switch or by automatic lock/unlock function
• Driver or passenger door switch is switched from OFF to ON
• Anti-hijack function is not activated
• Vehicle speed is 5 km/h (3 MPH) or less
REMOTE KEYLESS ENTRY SYSTEM
DLK-517
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000010435123
System Description
INFOID:0000000010435124
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp
at the same time as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.
OPERATION AREA
To ensure that the keyfob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.
ANTI-HIJACK FUNCTION
• When an LOCK signal is transmitted from keyfob, all doors are locked.
• When an UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change anti-hijack mode.
With CONSULT
Anti-hijack mode can be set to ON or OFF using CONSULT.
Refer to
DLK-521, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 4)"
Without CONSULT
• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 5 sec-
onds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
HAZARD REMINDER FUNCTION
Operation Description
JMKIB3324GB
Remote controller operation
Operation condition
Lock
• Key switch is off
• All doors are closed
Unlock
Key switch is off
OFF
→
ON
: 1 blinks
ON
→
OFF
: 3 blink
DLK-518
< SYSTEM DESCRIPTION >
[TYPE 4]
REMOTE KEYLESS ENTRY SYSTEM
When doors are locked or unlocked by keyfob button operation, BCM blinks hazard warning lamps as a
reminder.
AUTO DOOR LOCK FUNCTION
After door is unlocked by keyfob button operation and if 30 seconds or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
522, "MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)"
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock/unlock state, refer to
CONTROL SYSTEM : System Description"
Door lock operation
(With keyfob button)
Hazard warning lamp blink
Lock
Once
Unlock (all door unlock)
Twice
Unlock (anti-hijack operation)
Twice (quick)
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Key switch is ON
BACK DOOR OPENER SYSTEM
DLK-519
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SYSTEM
System Description
INFOID:0000000010479511
SYSTEM DIAGRAM
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• All doors are unlocked.
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-520
< SYSTEM DESCRIPTION >
[TYPE 4]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010435125
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but is not used.
DOOR LOCK
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Manual A/C
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
—
IMMU*
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
—
THEFT ALM*
×
×
×
—
RETAINED PWR*
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
DIAGNOSIS SYSTEM (BCM)
DLK-521
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 4)
INFOID:0000000010435126
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
MULTI REMOTE ENT
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
SHOCK SENSOR
NOTE:
This item is displayed, but cannot be monitored
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• “BD ULK” is displayed, but cannot be used
• “OTR ULK” is displayed, but cannot be used
DOOR LOCK IND
NOTE:
This item is displayed, but cannot be used
SUPER LOCK
NOTE:
This item is displayed, but cannot be used
DLK-522
< SYSTEM DESCRIPTION >
[TYPE 4]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)
INFOID:0000000010738154
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
DIAGNOSIS SYSTEM (BCM)
DLK-523
< SYSTEM DESCRIPTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK) (Type 4)
INFOID:0000000010503019
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Monitor Item
Contents
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
DLK-524
< SYSTEM DESCRIPTION >
[TYPE 4]
DIAGNOSIS SYSTEM (BCM)
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
BCM
DLK-525
< ECU DIAGNOSIS INFORMATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000010435129
ECU
Reference
BCM
DLK-526
< WIRING DIAGRAM >
[TYPE 4]
DOOR & LOCK SYSTEM
WIRING DIAGRAM
DOOR & LOCK SYSTEM
LHD
LHD : Wiring Diagram
INFOID:0000000011487294
JRKWE3958GB
DOOR & LOCK SYSTEM
DLK-527
< WIRING DIAGRAM >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWE3959GB
DLK-528
< WIRING DIAGRAM >
[TYPE 4]
DOOR & LOCK SYSTEM
JRKWE3960GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст