Qashqai J11. Door & Lock — part 45
BACK DOOR OPENER SWITCH
DLK-721
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR OPENER SWITCH
DLK-721, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010672330
1.
CHECK BACK DOOR OPENER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D94
4
Existed
Back door opener switch assembly
Condition
Continuity
Terminal
1
4
Back door opener
switch
Pressed
Existed
Released
Not existed
DLK-722
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
BACK DOOR REQUEST SWITCH
BACK DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000010672331
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “REQ SW-BD/TR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door request switch is OK.
NO
>> Refer to
DLK-722, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672332
1.
CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check voltage between back door opener switch assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair harness or connector.
3.
CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between back door opener switch assembly harness connector and ground.
Monitor item
Condition
Status
REQ SW-BD/TR
Back door request switch
Pressed
On
Released
Off
(+)
(–)
Voltage
Back door opener switch assembly
Connector
Terminal
D94
2
Ground
9 - 16 V
BCM
Back door opener switch assembly
Continuity
Connector
Terminal
Connector
Terminal
B4
6
D94
2
Existed
BCM
Ground
Continuity
Connector
Terminal
B4
6
Not existed
BACK DOOR REQUEST SWITCH
DLK-723
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR REQUEST SWITCH
DLK-723, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010672333
1.
CHECK BACK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D94
3
Existed
Back door opener switch assembly
Condition
Continuity
Terminal
2
3
Back door request switch
Pressed
Existed
Released
Not existed
DLK-724
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
COMBINATION METER BUZZER
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000010672334
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Touch “Buzzer 1”, “Buzzer 2” or “Buzzer 3” to check that it works normally.
Is the inspection result normal?
Yes
>> Buzzer (combination meter) is OK.
No
>> Refer to
DLK-724, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672335
1.
CHECK METER BUZZER CIRCUIT
WCS-44, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
DOOR LOCK ACTUATOR
DLK-725
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010672336
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-725, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010672337
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
LHD models
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D1
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D25
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
141
D1
3
Existed
148
2
DLK-726
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR LOCK ACTUATOR
RHD models
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010672338
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-725, "DRIVER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010672339
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
141
D25
3
Existed
148
2
BCM
Ground
Continuity
Connector
Terminal
M68
141
Not existed
148
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
141
Ground
Door lock and unlock switch
Lock
9 – 16 V
148
Unlock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
DOOR LOCK ACTUATOR
DLK-727
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LHD models
RHD models
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
LHD models
RHD models
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
Front door lock assembly
(passenger side)
Connector
Terminal
D25
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
(+)
(–)
Condition
Voltage
Front door lock assembly
(passenger side)
Connector
Terminal
D1
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M68
139
D25
2
Existed
141
3
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M68
139
D1
2
Existed
141
3
BCM
Ground
Continuity
Connector
Terminal
M68
139
Not existed
141
DLK-728
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR LOCK ACTUATOR
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR LH
REAR LH : Component Function Check
INFOID:0000000010672340
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-725, "DRIVER SIDE : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000010672341
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH connector.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
139
Ground
Door lock and unlock switch
Unlock
9 – 16 V
141
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Rear door lock assembly LH
Connector
Terminal
D51
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D51
2
Existed
125
3
DOOR LOCK ACTUATOR
DLK-729
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR RH
REAR RH : Component Function Check
INFOID:0000000010672342
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-725, "DRIVER SIDE : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000010672343
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH connector.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH.
NO
>> GO TO 2.
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
125
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Door lock and unlock switch
Unlock
9 – 16 V
125
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Rear door lock assembly RH
Connector
Terminal
D64
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
DLK-730
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR LOCK ACTUATOR
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D64
2
Existed
125
3
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
125
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Door lock and unlock switch
Unlock
9 – 16 V
125
Lock
DOOR LOCK AND UNLOCK SWITCH
DLK-731
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010672344
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-731, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010672345
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check signal between power window main switch harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1.
Disconnect BCM connector and front power window switch (passenger side) connector.
2.
Check continuity between BCM harness connector and power window main switch harness connector.
LHD models
Monitor item
Condition
Status
CDL LOCK SW
Door lock and unlock switch
Lock
ON
Unlock
OFF
CDL UNLOCK SW
Lock
OFF
Unlock
ON
(+)
(–)
Voltage
Power window main switch
Connector
Terminal
D10
3
Ground
9 - 16 V
15
(+)
(–)
Voltage
Power window main switch
Connector
Terminal
D30
3
Ground
9 - 16 V
15
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D10
3
Existed
80
15
DLK-732
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR LOCK AND UNLOCK SWITCH
RHD models
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-68, "POWER WINDOW MAIN SWITCH :
NO
>> INSPECTION END
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010672346
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-732, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010672347
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check signal between front power window switch (passenger side) harness connector and ground.
LHD models
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D30
3
Existed
80
15
BCM
Ground
Continuity
Connector
Terminal
M70
50
Not existed
80
Monitor item
Condition
Status
CDL LOCK SW
Door lock and unlock switch
Lock
ON
Unlock
OFF
CDL UNLOCK SW
Lock
OFF
Unlock
ON
(+)
(–)
Voltage
Front power window switch (passenger side)
Connector
Terminal
D37
1
Ground
9 - 16 V
2
DOOR LOCK AND UNLOCK SWITCH
DLK-733
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RHD models
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1.
Disconnect BCM connector and power window main switch connector.
2.
Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.
LHD models
LHD models
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
DOW SWITCH (PASSENGER SIDE) : Removal and Installation"
NO
>> INSPECTION END
(+)
(–)
Voltage
Front power window switch (passenger side)
Connector
Terminal
D7
1
Ground
9 - 16 V
2
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D37
1
Existed
80
2
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D7
1
Existed
80
2
BCM
Ground
Continuity
Connector
Terminal
M70
50
Not existed
80
DLK-734
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR LOCK STATUS INDICATOR
DOOR LOCK STATUS INDICATOR
Component Function Check
INFOID:0000000010672348
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK IND” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock status indicator is OK.
NO
>> Refer to
DLK-734, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672349
1.
CHECK DOOR LOCK STATUS INDICATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect indicator unit connector.
3.
Check voltage between indicator unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace indicator unit.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK STATUS INDICATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and indicator unit harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
Monitor item
Status
DOOR LOCK IND
ON
Door lock status indicator
Turns ON
OFF
Turns OFF
(+)
(–)
Voltage
Indicator unit
Connector
Terminal
M4
5
Ground
9 – 16 V
BCM
Indicator unit
Continuity
Connector
Terminal
Connector
Terminal
M69
111
M4
5
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
111
Not existed
DOOR REQUEST SWITCH
DLK-735
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000010672350
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Front door request switch is OK.
NO
>> Refer to
DLK-735, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010672351
1.
CHECK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning front outside handle assembly connector.
3.
Check voltage between malfunctioning front outside handle assembly harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between malfunctioning front outside handle assembly harness connector and BCM har-
ness connector.
LHD models
Monitor item
Condition
Status
REQ SW -DR
Driver side door request switch
Pressed
ON
Released
OFF
REQ SW -AS
Passenger side door request switch
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Front outside handle assembly
Connector
Terminal
Driver side
D8
3
Ground
9 – 16 V
Passenger side
D38
(+)
(–)
Voltage
Front outside handle assembly
Connector
Terminal
Driver side
D39
3
Ground
9 – 16 V
Passenger side
D9
Front outside handle assembly
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
D8
3
M69
105
Existed
Passenger side
D38
82
DLK-736
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
DOOR REQUEST SWITCH
RHD models
3.
Check continuity between malfunctioning front outside handle assembly harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between malfunctioning front outside handle assembly harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR REQUEST SWITCH
DLK-736, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning outside handle grip.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010672352
1.
CHECK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
Front outside handle assembly
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
D39
3
M69
105
Existed
Passenger side
D9
82
Front outside handle assembly
Ground
Continuity
Connector
Terminal
Driver side
D8
3
Not existed
Passenger side
D38
Front outside handle assembly
Ground
Continuity
Connector
Terminal
Driver side
D39
3
Not existed
Passenger side
D9
Front outside handle assembly
Ground
Continuity
Connector
Terminal
Driver side
D8
4
Existed
Passenger side
D38
Front outside handle assembly
Ground
Continuity
Connector
Terminal
Driver side
D39
4
Existed
Passenger side
D9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст