Qashqai J11. Door & Lock — part 49
HOOD
DLK-785
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Hood assembly
2.
Front combination lamp
3.
Front fender assembly
4.
Hood bumper rubber
5.
Hood hinge
6.
Hood lock assembly
: Vehicle front
:N·m (kg-m, ft-lb)
:Body grease
JMKIB4355GB
DLK-786
< REMOVAL AND INSTALLATION >
[TYPE 5]
HOOD
Unit: mm [in]
*: No more than 2 times left to right or right to left.
Fitting Adjustment Procedure
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove hood lock assembly.
3.
Adjust the surface height of hood assembly, front fender assembly, and front combination lamp according
to the specified value, by rotating hood bumper rubber (body side).
4.
Loosen hood hinge mounting bolts.
5.
Adjust clearance of hood according to the specified value, by moving the hood assembly.
6.
Tighten hood hinge mounting bolts to the specified torque.
7.
Move hood lock assembly laterally until the center of primary striker and hood lock assembly are vertical
when viewed from the front.
8.
Position hood lock assembly and engage primary striker. Check hood lock assembly and primary striker
for looseness.
9.
Tighten hood lock assembly mounting bolts and nut to the specified torque.
10. Rotate bumper rubber 1/2 of a rotation counterclockwise in upward direction.
11. After adjusting, check that hood opens and closes normally. Refer to
.
12. Install front grille. Refer to
EXT-26, "Removal and Installation"
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000010678777
REMOVAL
1.
Remove hood assembly. Refer to
DLK-784, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove upper mounting bolt of front fender assembly. Refer to
DLK-792, "Removal and Installation"
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply touch-up paint to the body color if the paint around the hinge is peeled off during removal.
• After installation, perform hood fitting adjustment. Refer to
DLK-784, "HOOD ASSEMBLY : Adjust-
• Before installation of hood, apply anticorrosive agent onto the mounting surface of the hood hinge.
• Check hood hinge rotating part for poor lubrication. Refer to
DLK-787, "HOOD HINGE : Inspection"
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front combination
lamp
A – A
C
Clearance
4.0 – 9.0
[0.157 – 0.354]
≤
3.0
[0.118]
D Surface height
0.0
[0.000]
—
Hood – Front fender
B – B
E
Clearance
*
—
F Surface height
≤
3.0
[0.118]
—
HOOD
DLK-787
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD HINGE : Inspection
INFOID:0000000010678778
Check hood hinge rotating part for poor lubrication. Apply body
grease if necessary.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010678779
REMOVAL
CAUTION:
Two workers are required to support the hood.
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported with appropriate material when removing
hood assembly.
2.
Remove hood support rod from hood rod grommet.
3.
Remove hood rod grommet from hood assembly.
INSTALLATION
Install in the reverse order of removal.
HOOD INSULATOR
HOOD INSULATOR : Removal and Installation
INFOID:0000000010678780
REMOVAL
1.
Fully open hood assembly.
2.
Remove hood rod clamp from hood assembly.
3.
Remove hood insulator clips, and then remove hood insulator.
INSTALLATION
Install in the reverse order of removal.
: Body grease
JMKIB2933ZZ
DLK-788
< REMOVAL AND INSTALLATION >
[TYPE 5]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
MR20DD
MR20DD : Exploded View
INFOID:0000000010678783
T/M models
JMKIB3632GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
5.
Air guide plate
:N·m (kg-m, ft-lb)
RADIATOR CORE SUPPORT
DLK-789
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CVT models
MR20DD : Removal and Installation
INFOID:0000000010678784
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-811, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
.
10. Remove A/C pipe bracket mounting bolt. Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
R9M
JMKIB3633GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
5.
Air guide plate
:N·m (kg-m, ft-lb)
DLK-790
< REMOVAL AND INSTALLATION >
[TYPE 5]
RADIATOR CORE SUPPORT
R9M : Exploded View
INFOID:0000000010678787
T/M models
CVT models
JMKIB3299GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3300GB
RADIATOR CORE SUPPORT
DLK-791
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
R9M : Removal and Installation
INFOID:0000000010678788
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-528, "Removal and Installation"
.
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-811, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
.
10. Remove A/C pipe bracket mounting bolt. Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
DLK-792
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000010678789
Removal and Installation
INFOID:0000000010678790
CAUTION:
Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Remove fillet molding. Refer to
EXT-38, "Removal and Installation"
2.
Remove fender protector. Refer to
EXT-33, "Removal and Installation"
3.
Remove front bumper fascia assembly and bumper side bracket. Refer to
EXT-20, "Removal and Installa-
4.
Remove front combination lamp. Refer to
EXL-319, "Removal and Installation"
(HALOGEN HEADLAMP)
EXL-162, "Removal and Installation"
(LED HEADLAMP).
5.
Remove front fender seal.
6.
Remove front fender assembly mounting bolts.
1.
Front fender seal
2.
Front fender assembly
3.
Hoodledge cover
: Pawl
: N·m (kg-m, in-lb)
JMKIB3315GB
FRONT FENDER
DLK-793
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Remove front fender stiffener (2) from the vehicle body while
carefully pulling upper portion of front fender (1) toward vehicle
outside.
8.
Remove front fender assembly.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, be careful to not deform the front fender while performing the procedure and remov-
ing the viscous urethane foam a little at a time.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• After installation, adjust the following part.
- Hood assembly: Refer to
DLK-784, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-795, "DOOR ASSEMBLY : Adjustment"
.
: Vehicle front
JMKIA5633ZZ
DLK-794
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT DOOR
FRONT DOOR
Exploded View
INFOID:0000000010678791
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010678792
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove front door harness grommet from vehicle body side, and then pull out front door harness.
2.
Disconnect front door harness connector.
3.
Remove mounting bolt of door check link on the vehicle body.
4.
Remove door hinge mounting nuts of door side, and then remove door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Front door panel
2.
Grommet
3.
TORX bolt
4.
Door striker
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3248GB
FRONT DOOR
DLK-795
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-795, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-797, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-797, "DOOR CHECK LINK : Removal and Installation"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010678793
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
DLK-796
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT DOOR
Fitting Adjustment Standard
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove front fender. Refer to
DLK-792, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on vehicle body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Apply body grease if necessary. Refer to
DLK-797, "DOOR HINGE : Inspection"
8.
Install front fender. Refer to refer to
DLK-792, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010678794
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-795, "DOOR ASSEMBLY : Adjust-
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010678795
REMOVAL
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front fender – Front door
A – A
H
Clearance
3.3 – 5.3
[0.130 – 0.209]
I
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
FRONT DOOR
DLK-797
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-792, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-794, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-795, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010678796
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010678797
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove front door speaker.
a.
Disconnect front door speaker harness connector.
b.
Remove front door speaker mounting bolts, and then remove front door speaker.
4.
Remove check link mounting bolts of vehicle body side.
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
: Body grease
JMKIB0321ZZ
DLK-798
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT DOOR
DOOR CHECK LINK : Inspection
INFOID:0000000010678798
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
REAR DOOR
DLK-799
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000010678799
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010678800
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door harness grommet from vehicle body side, and then pull out rear door harness.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolt of door check link on the vehicle.
4.
Remove door hinge mounting nuts of door side, and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Rear door panel
2.
Grommet
3.
TORX bolt
4.
Door striker
5.
Door check link
6.
Door hinge (lower)
7.
Door hinge (upper)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3250GB
DLK-800
< REMOVAL AND INSTALLATION >
[TYPE 5]
REAR DOOR
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-800, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-802, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-803, "DOOR CHECK LINK : Inspection"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010678801
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст