Qashqai J11. Door & Lock — part 60
REAR DOOR LOCK
DLK-961
< REMOVAL AND INSTALLATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Slide outside handle bracket toward rear of vehicle to remove.
9.
Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
DLK-962
< REMOVAL AND INSTALLATION >
[TYPE 6]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000010678901
Removal and Installation
INFOID:0000000010678902
REMOVAL
1.
Remove back door trim finisher lower. Refer to
INT-31, "Removal and Installation"
2.
Disconnect back door lock harness connector.
3.
Remove back door assembly mounting bolts, and then remove back door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check back door open/close, and lock/unlock operation.
• Check door lock assembly for poor lubrication. Refer to
1.
Back door panel
2.
Back door lock assembly
: N·m (kg-m, ft-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3271GB
BACK DOOR LOCK
DLK-963
< REMOVAL AND INSTALLATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Inspection
INFOID:0000000010678903
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
: Body grease
JMKIB0629ZZ
DLK-964
< REMOVAL AND INSTALLATION >
[TYPE 6]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000010678904
LHD models
JMKIB3264ZZ
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
FUEL FILLER LID OPENER
DLK-965
< REMOVAL AND INSTALLATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RHD models
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000010678905
REMOVAL
1.
Fully open fuel filler lid assembly.
JMKIB3263ZZ
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
DLK-966
< REMOVAL AND INSTALLATION >
[TYPE 6]
FUEL FILLER LID OPENER
2.
Remove fuel mounting pin (1).
3.
Remove fixing screws, and then remove fuel filler lid assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the fixing screws.
• Apply anti-corrosion wax to mounting surface of fixing screw and fuel filler lid to prevent rust.
NOTE:
The following table shows the specified values for checking normal installation status.
Unit: mm [in]
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000010678906
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage lower finisher RH. Refer to
.
3.
In the order of 1
→
2 as shown in the figure, rotate and disengage
fuel filler lid lock assembly, and then remove fuel filler lid lock
assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
In the order of 1
→
4 as shown in the figure. Disengage fuel filler
lid opener cable (1). Remove fuel filler lid opener cable while
pressing stopper pin (2).
JMKIB3183ZZ
Clearance
Evenness
Fuel filler lid – Body side outer
3.7 – 5.3
(0.146 – 0.209)
(-1.0) – (+1.0)
[(-0.039) – (+0.039)]
: Pawl
: Vehicle front
JMKIB1094ZZ
JMKIA5719ZZ
FUEL FILLER LID OPENER
DLK-967
< REMOVAL AND INSTALLATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000010678907
REMOVAL
LHD models
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner LH and rear kicking plate inner LH. Refer to
.
4.
Remove dash side finisher LH. Refer to
INT-18, "Removal and Installation"
.
5.
Remove center pillar lower garnish LH. Refer to
INT-18, "Removal and Installation"
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
RHD models
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner RH and rear kicking plate inner RH. Refer to
.
4.
Remove dash side finisher RH. Refer to
INT-18, "Removal and Installation"
5.
Remove center pillar lower garnish RH. Refer to
INT-18, "Removal and Installation"
.
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
JMKIA5901ZZ
JMKIA5672ZZ
DLK-968
< REMOVAL AND INSTALLATION >
[TYPE 6]
FUEL FILLER LID OPENER
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse cable protector. Always replace it with a new one when it is removed.
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
DOOR SWITCH
DLK-969
< REMOVAL AND INSTALLATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Removal and Installation
INFOID:0000000010672618
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2173ZZ
DLK-970
< REMOVAL AND INSTALLATION >
[TYPE 6]
KEYFOB BATTERY
KEYFOB BATTERY
Removal and Installation
INFOID:0000000010672619
REMOVAL
1.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
2.
Replace the battery with new one.
CAUTION:
• When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.
• After replacing the battery, check that all Intelligent Key functions work normally.
INSTALLATION
Install in the reverse order of removal.
JMKIB3016ZZ
Battery replacement
:Coin-type lithium battery
(CR2032)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст