Nissan Rogue (2020 year). Manual — part 30
CLEANING
If your windshield is not clear after using
the windshield-washer or if a wiper blade
chatters when running, wax or other mate-
rial may be on the blade or windshield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild de-
tergent. Then rinse the blades with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.
CAUTION
Worn windshield wiper blades can
damage the windshield and impair
driver vision.
REPLACING
Replace the wiper blades if they are worn.
To replace the windshield wiper blades, fol-
low the procedure below:
1. When ignition switch is ON or within
60 seconds after placing the ignition
switch from the ON to OFF position,
place the windshield wiper and washer
lever into the OFF position.
2. Rapidly lift the windshield wiper and
washer lever
䊊
A
upwards twice within
0.5 seconds. This action will cause the
wipers to automatically take the ser-
vice position.
LDI2476
WINDSHIELD WIPER BLADES
8-20
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Once the wipers are in the service po-
sition, push the release tab
䊊
B
.
4. Move the wiper blade down
䊊
C
and re-
move.
5. Insert the new wiper blade onto the
wiper arm until it clicks into place.
6. Rotate the wiper blade so the dimple is
in the groove.
7. Finally, lift the windshield wiper and
washer lever to the mist position
䊊
D
once and release. This action will cause
the wipers to resume the set position.
CAUTION
∙ After wiper blade replacement, return
the wiper arm to its original position;
otherwise it may be damaged when
the hood is opened.
∙ Make sure the wiper blades contact
the glass; otherwise the arms may be
damaged from wind pressure.
If you wax the surface of the hood, be care-
ful not to let wax get into the washer nozzle
䊊
F
. This may cause clogging or improper
windshield-washer operation. If wax gets
into the nozzle, remove it with a needle or
small pin
䊊
E
.
LDI2475
LDI2477
LDI2820
Do-it-yourself
8-21
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Rear window wiper blade
If checking or replacement is required, it is
recommended that you visit a NISSAN
dealer for this service.
If the brakes do not operate properly, have
the brakes checked. It is recommended
that you visit a NISSAN dealer for this ser-
vice.
Self-adjusting brakes
Your vehicle is equipped with self-adjusting
brakes.
The front and rear disc-type brakes self-
adjust every time the brake pedal is ap-
plied.
WARNING
Have your brake system checked if the
brake pedal height does not return to
normal. It is recommended that you
visit a NISSAN dealer for this service.
Brake pad wear indicators
The disc brake pads on your vehicle have
audible wear indicators. When a brake pad
requires
replacement,
a
high
pitched
scraping or screeching sound will be heard
when the vehicle is in motion. The noise will
be heard whether or not the brake pedal is
depressed. Have the brakes checked as
soon as possible if the wear indicator
sound is heard.
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is nor-
mal and does not affect the function or
performance of the brake system.
Proper brake inspection intervals should
be followed. For additional information re-
garding brake inspections, refer to the ap-
propriate maintenance schedule informa-
tion in the "Maintenance and schedules"
section of this manual.
BRAKES
8-22
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If any electrical equipment does not oper-
ate, check for an open fuse.
Fuses are used in the passenger and en-
gine compartment. Spare fuses are pro-
vided and can be found in the passenger
compartment fuse box.
When installing a fuse make sure the fuse is
installed in the fuse box securely.
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire
If any electrical equipment does not come
on, check for an open fuse.
For checking and replacing fuses, it is rec-
ommended that you visit a NISSAN dealer
for this service.
Fusible links
If the electrical equipment does not oper-
ate and fuses are in good condition, check
the fusible links. If any of these fusible links
are melted, replace with only Genuine
NISSAN parts.
LDI2385
LDI2840
FUSES
Do-it-yourself
8-23
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not oper-
ate, check for an open fuse.
NOTE:
The fuse box is located on the driver’s
side of the instrument panel.
1. Be sure the ignition switch and the
headlight switch are OFF.
2. Remove the fuse box cover with a suit-
able tool. Use a cloth to avoid damag-
ing the trim.
3. Locate the fuse that needs to be re-
placed.
4. Remove the fuse with the fuse puller
䊊
A
.
5. If the fuse is open
䊊
B
, replace it with an
equivalent good fuse
䊊
C
.
6. Push the fuse box cover to install.
If a new fuse also opens, have the electrical
system checked and repaired, It is recom-
mended that you visit a NISSAN dealer for
this service.
LDI2821
LDI2760
8-24
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
Be careful not to allow children to swal-
low the battery or removed parts.
NISSAN INTELLIGENT KEY® (if so
equipped)
Replace the battery in the Intelligent Key as
follows:
1. Remove the mechanical key from the
Intelligent Key.
2. Insert a small flathead screwdriver
䊊
A
into the slit
䊊
B
of the corner and twist it
to separate the upper part from the
lower part. Place a cloth over the
screwdriver to protect the casing.
LDI2001
BATTERY REPLACEMENT
Do-it-yourself
8-25
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Replace the battery with a new one.
Recommended battery: CR2032 or
equivalent.
∙ Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
∙ Hold the battery by the edges. Hold-
ing the battery across the contact
points will seriously deplete the stor-
age capacity.
∙ Make sure that the + side faces the
bottom of the lower part.
4. Close the lid securely as illustrated with
䊊
C
and
䊊
D
.
5. Operate the buttons to check the op-
eration.
It is recommended that you visit a NISSAN
dealer if you need assistance for replace-
ment.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Note:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
For Canada:
This
device
complies
with
Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.
LDI2637
8-26
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
NISSAN JACKKNIFE KEY (if so
equipped)
Replace the battery in the jackknife key as
follows:
䊊
1
Hold jackknife key button side up. In-
sert a small screwdriver into the slit of
the corner and twist it to separate the
upper part from the lower part. Use a
cloth to protect the casing.
䊊
2
Remove old battery.
䊊
3
Replace the battery with a new one.
Recommended battery: CR2032 or
equivalent.
∙ Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
∙ Hold the battery by the edges. Hold-
ing the battery across the contact
points will seriously deplete the stor-
age capacity.
䊊
4
Close lid securely as illustrated.
Operate the buttons to check the opera-
tion.
It is recommended that you visit a NISSAN
dealer if you need assistance for replace-
ment.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
LDI2354
Do-it-yourself
8-27
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Note: Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the user’s
authority to operate the equipment.
For Canada:
This
device
complies
with
Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.
HEADLIGHTS
For additional information on headlight
bulb replacement, refer to the instructions
outlined in this section.
Replacing the halogen headlight
bulb (if so equipped)
The headlight is a semi-sealed beam type
which uses a replaceable headlight (halo-
gen) bulb. They can be replaced from inside
the engine compartment without remov-
ing the headlight assembly.
If headlight bulb replacement is required, it
is recommended that you visit a NISSAN
dealer for this service.
CAUTION
∙ Aiming is not necessary after replac-
ing the bulb. When aiming adjustment
is necessary, it is recommended that
you visit a NISSAN dealer for this
service.
∙ Do not leave the headlight assembly
open without a bulb installed for a
long period of time. Dust, moisture,
smoke, etc. entering the headlight
body may affect bulb performance.
Remove the bulb from the headlight
assembly just before a replacement
bulb is installed.
∙ Only touch the base when handling
the bulb. Never touch the glass enve-
lope. Touching the glass could signifi-
cantly affect bulb life and/or head-
light performance.
∙ High pressure halogen gas is sealed
inside the halogen bulb. The bulb may
break
if
the
glass
envelope
is
scratched or the bulb is dropped.
∙ Use the same number and wattage as
shown in the chart.
Fog may temporarily form inside the lens
of the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction. If
large drops of water collect inside the lens,
it is recommended that you visit a NISSAN
dealer for servicing.
LIGHTS
8-28
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Replacing the LED headlight bulb
(if so equipped)
If LED headlight bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.
FOG LIGHTS (if so equipped)
For additional information on fog light bulb
replacement, refer to the instructions out-
lined in this section.
Replacing the fog light bulb
If bulb replacement is required, it is recom-
mended that you visit a NISSAN dealer for
this service.
CAUTION
∙ High pressure halogen gas is sealed
inside the halogen bulb. The bulb may
break
if
the
glass
envelope
is
scratched or the bulb is dropped.
∙ When handling the bulb, do not touch
the glass envelope.
∙ Use the same number and wattage as
originally installed as shown in the
chart.
∙ Do not leave the bulb out of the fog
light for a long period of time as dust,
moisture and smoke may enter the
fog light body and affect the perfor-
mance of the fog light.
Do-it-yourself
8-29
-------------------------------------------------------------------------------------------------------------------------------------------------------------
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
Headlight assembly (Type A) (if so equipped)*
High
65
H9
Low
55
H11
Turn
28/8
7444NA
Side marker
5
W5W
Daytime running lights/clearance
lights*
—
—
Headlight assembly (Type B) (if so equipped)*
High
—
—
Low
—
—
Turn
28/8
7444NA
Side marker
—
—
Daytime running lights/clearance
lights*
—
—
Fog lights (if so equipped)*
35
H8
Courtesy light*
—
—
Door mirror turn signal light (if so equipped)*
—
—
Map light*
—
—
Glove box light*
1.4
—
Vanity mirror light (if so equipped)
1.8
—
Room light (if so equipped)
8
—
Personal lights (if so equipped)
8
—
Cargo light*
5
—
High-mounted stop light*
—
—
Rear combination light*
Stop
21
W21W
Tail/Stop
—
—
Turn
21
WY21W
Side marker
5
W5W
Backup (reversing) assembly*
Backup
18
921
Tail
—
—
License plate light*
5
W5W
* It is recommended that you visit a NISSAN dealer for replacement.
Always check with the Parts Department at a NISSAN dealer for the latest parts information.
LDI3227
8-30
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
1.
Headlight assembly
2
Map light
3
Personal light (if so equipped)
4.
Door mirror turn signal light (if so
equipped)
5.
Fog light (if so equipped)
6.
Daytime running light
7.
Room light (if so equipped)
8.
Cargo light
9.
High mounted stop light
10.
License plate light
11.
Backup (reversing) assembly
12.
Rear combination light
Replacement procedures
All other lights are either type A, B, C or D.
When replacing a bulb, first remove the
lens, lamp and/or cover.
Indicates bulb removal
Indicates bulb installation
WDI0263
Do-it-yourself
8-31
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If you have a flat tire, refer to “Flat tire” in
the “In case of emergency” section of
this manual.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
WARNING
Radio waves could adversely af-
fect electric medical equipment.
Those who use a pacemaker
should contact the electric medi-
cal equipment manufacturer for
the possible influences before
use.
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS).
It monitors tire pressure of all tires
except the spare. When the low tire
pressure warning light is lit and the
“Tire Pressure Low - Add Air” warning
appears in the vehicle information
display, one or more of your tires is
significantly
under-inflated.
If
equipped, the system also displays
pressure of all tires (except the spare
tire) on the display screen by send-
ing a signal from a sensor that is
installed in each wheel.
The TPMS will activate only when the
vehicle is driven at speeds above
16 mph (25 km/h). Also, this system
may not detect a sudden drop in tire
pressure (for example a flat tire while
driving).
For additional information, refer to
“Low tire pressure warning light” in
the “Instruments and controls” sec-
tion, “Tire Pressure Monitoring Sys-
tem (TPMS)” in the “Starting and driv-
ing” section and “Flat tire” in the “In
case of emergency” section of this
manual.
Tire inflation pressure
Check the tire pressures (including
the spare) often and always prior to
long distance trips. The recom-
mended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S.
certification label or the Tire and
Loading Information label under the
“Cold Tire Pressure” heading. The Tire
and Loading Information label is af-
fixed to the driver side center pillar.
Tire pressures should be checked
regularly because:
∙ Most tires naturally lose air over
time.
∙ Tires can lose air suddenly when
driven over potholes or other ob-
jects or if the vehicle strikes a
curb while parking.
The
tire
pressures
should
be
checked when the tires are cold. The
tires are considered COLD after the
vehicle has been parked for 3 or
more hours, or driven less than 1 mile
(1.6 km) at moderate speeds.
The TPMS with Easy-Fill Tire Alert
provides visual and audible signals
outside the vehicle for inflating the
tires to the recommended COLD tire
pressure. For additional information,
refer to “TPMS with Easy-Fill Tire
Alert” in the “Starting and driving”
section of this manual.
WHEELS AND TIRES
8-32
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Incorrect tire pressure, including
under inflation, may adversely af-
fect tire life and vehicle handling.
WARNING
∙ Improperly inflated tires can fail
suddenly
and
cause
an
accident.
∙ The Gross Vehicle Weight Rating
(GVWR)
is
located
on
the
F.M.V.S.S./C.M.V.S.S.
certifica-
tion label. The vehicle weight
capacity is indicated on the Tire
and Loading Information label.
Do not load your vehicle beyond
this capacity. Overloading your
vehicle may result in reduced
tire life, unsafe operating condi-
tions due to premature tire fail-
ure, or unfavorable handling
characteristics and could also
lead to a serious accident. Load-
ing beyond the specified capac-
ity may also result in failure of
other vehicle components.
∙ Before taking a long trip, or
whenever you heavily load your
vehicle, use
a
tire
pressure
gauge to ensure that the tire
pressures are at the specified
level.
∙ For additional information re-
garding tires, refer to “Impor-
tant Tire Safety Information”
(US) or “Tire Safety Information”
(Canada) in the Warranty Infor-
mation Booklet.
Do-it-yourself
8-33
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tire and Loading Information
label
䊊
1
Seating capacity: The maximum
number of occupants that can
be seated in the vehicle.
䊊
2
Tire size - refer to “Tire labeling” in
this section.
䊊
3
Cold tire pressure: Inflate the
tires to this pressure when the
tires are cold. Tires are consid-
ered COLD after the vehicle has
been parked for 3 or more hours,
or driven less than 1 mile (1.6 km)
at moderate speeds. The rec-
ommended cold tire inflation is
set by the manufacturer to pro-
vide the best balance of tire
wear, vehicle handling, drivability,
tire noise, etc., up to the vehicle’s
GVWR.
䊊
4
Original tire size: The size of the
tires originally installed on the
vehicle at the factory.
䊊
5
Spare tire size (if so equipped).
䊊
6
Vehicle load limit: Refer to “Ve-
hicle loading information” in the
“Technical and consumer infor-
mation” section of this manual.
LDI2737
8-34
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Checking tire pressure
1. Remove the valve stem cap from
the tire.
2. Press
the
pressure
gauge
squarely onto the valve stem. Do
not press too hard or force the
valve stem sideways, or air will
escape. If the hissing sound of air
escaping from the tire is heard
while checking the pressure, re-
position the gauge to eliminate
this leakage.
3. Remove the gauge.
4. Read the tire pressure on the
gauge stem and compare to the
specification shown on the Tire
and Loading Information label.
5. Add air to the tire as needed. If
too much air is added, press the
core of the valve stem briefly
with the tip of the gauge stem to
release pressure. Recheck the
pressure and add or release air
as needed.
6. Install the valve stem cap.
7. Check the pressure of all other
tires, including the spare.
Size
Cold Tire Infla-
tion Pressure
Front and Rear
Original Tire:
225/65R17 102H
33 psi, 230 kPa
Front and Rear
Original Tire:
225/60R18 100H
33 psi, 230 kPa
Front and Rear
Original Tire:
225/55R19 99H
33 psi, 230 kPa
Spare Tire:
T155/90D17 101M
60 psi, 420 kPa
Spare Tire:
T145/90D16
106M
60 psi, 420 kPa
LDI0393
Do-it-yourself
8-35
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст