Nissan March K13. Manual — part 324
EXT-18
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
ROOF SIDE MOLDING
Exploded View
INFOID:0000000006052875
Removal and Installation
INFOID:0000000006052876
REMOVAL
1.
Disengage roof side molding fixing clip, using remover tool (A).
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
2.
Remove roof side molding from front end.
CAUTION:
Never pull the roof side molding strongly.
INSTALLATION
Install in the reverse order of removal.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
1.
Roof side molding
2.
Roof side molding clip
3.
Roof panel
4.
Body side outer panel
Refer to
for symbols in the figure.
JMKIA5396ZZ
: Clip
JMKIA5401ZZ
ROOF SIDE MOLDING
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• Use double-faced adhesive tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Never wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N (2.0 Kg - 4.41 lb)
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
EXT-20
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000006052877
Removal and Installation
INFOID:0000000006052878
REMOVAL
FRONT DOOR OUTSIDE MOLDING
1.
Fully open front door glass.
2.
Twist door outside molding toward the outside of the vehicle,
and then lift up and remove it while disengaging the pawls.
REAR DOOR OUTSIDE MOLDING
1.
Fully open door window.
1.
Front door panel
2.
Front door outside molding
3.
Rear door panel
4.
Rear door outside molding
JMKIA5397ZZ
JMKIA3824ZZ
DOOR OUTSIDE MOLDING
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Twist door outside molding to ward the outside of the vehicle,
and then lift up and remove it while disengaging the pawls.
INSTALLATION
Install in the reverse order of removal.
JMKIA3825ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст