Nissan March K13. Manual — part 293
EXHAUST SYSTEM
EX-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000005988498
Removal and Installation
INFOID:0000000005988499
REMOVAL
• Disconnect each joint and mounting.
• Remove heated oxygen sensor 2 with following procedure:
- Using heated oxygen sensor wrench [SST: KV10114400] (A),
removal heated oxygen sensor 2 (1).
CAUTION:
Be careful not to damage heated oxygen sensor 2.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Always replace seal bearings with new ones when reassembling.
1.
Seal bearing
2.
Spring
3.
Heated oxygen sensor 2
4.
Exhaust front tube
5.
Seal bearing
6.
Mounting bracket
7.
Center muffler
8.
Ring gasket
9.
Main muffler
JPBIA3372GB
2
: Exhaust front tube
JPBIA3468ZZ
EX-6
< REMOVAL AND INSTALLATION >
EXHAUST SYSTEM
• Discard any heated oxygen sensor 2 which has been dropped onto a hard surface such as a con-
crete floor. Use a new one.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner [commercial service tool: J-43897-18 or J-43897-12] and apply anti-seize
lubricant (commercial service tool).
• Never over torque heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
• If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, remove them.
• When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid gas
leakage.
• When installing each mounting rubber, use silicon oil to avoid twisting.
• Temporarily tighten mounting nuts and bolts. Check each part for unusual interference and mount-
ing rubber interference, and then tighten them to the specified torque.
• When installing each mounting rubber, avoid twisting or unusual extension in up/down, front/rear
and right/left directions.
Exhaust Manifold to Exhaust Front Tube
1.
Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown in the figure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2.
With spring, tighten nut.
CAUTION:
• Fasten stud bolts to the flange of exhaust manifold side to the specified torque before fastening
mounting nuts.
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that stud bolt does not interfere with mounting hole of exhaust front tube (
).
3.
After installing, check that stud bolt does not interfere with mounting hole of exhaust front tube.
Exhaust Front Tube to Center Muffler
1.
Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown in the figure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2.
With spring, tighten bolt.
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that bolt does not interfere with mounting hole of center muffler (
).
3.
After installing, check that bolt does not interfere with mounting hole of center muffler.
Inspection
INFOID:0000000005988500
INSPECTION AFTER INSTALLATION
• Check clearance between tail tube and rear bumper is even.
3
: Spring
4
: Nut
5
: Stud bolt
6
: Exhaust front tube
JPBIA2372ZZ
3
: Spring
4
: Bolt
5
: Center muffler
JPBIA2174ZZ
EXHAUST SYSTEM
EX-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
• With engine running, check exhaust tube joints for gas leakage and unusual noises.
• Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
EXL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
EXL
A
B
EXL
N
O
P
CONTENTS
EXTERIOR LIGHTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
EXTERIOR LIGHTING SYSTEM . . . . . . . .....
EXTERIOR LIGHTING SYSTEM : Component
Parts Location . . . . . . . . . . . . . . ...
EXTERIOR LIGHTING SYSTEM :
Component Description . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
HEADLAMP SYSTEM . . . . . . . . . . . .....
HEADLAMP SYSTEM : System Diagram . . . .....
HEADLAMP SYSTEM : System Description . . .....
FRONT FOG LAMP SYSTEM . . . . . . . . .....
FRONT FOG LAMP SYSTEM : System Diagram . ..
FRONT FOG LAMP SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ....
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM . . . . . . . . . . . . . . . . . ..
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram . . . . . . . . . ..
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description . . . . . . . .....
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM . . . . . . . . . . . . . . . . . ..
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Diagram . . . . . . . . . ..
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Description . . . . . . . .....
EXTERIOR LAMP BATTERY SAVER SYSTEM . .....
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Diagram . . . . . . . . . . . . . ..
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Description . . . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) . . . . . . . . . . . . . . ...
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT-III Function (BCM -
FLASHER) . . . . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) . . . . . . . . . . . . . . ...
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT-III Function (BCM -
FLASHER) . . . . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN-
TELLIGENT KEY SYSTEM) . . . . . . . .
Diagnosis Description . . . . . . . . . . . ..
CONSULT-III Function (IPDM E/R) . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT
INTELLIGENT KEY SYSTEM) . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст