Nissan March K13. Manual — part 33
PREPARATION
BR-5
< PREPARATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005986566
Tool name
Description
Brake pressure gauge
Check brake fluid pressure
Handy vacuum pump
• Air tight
• Inspection of check valve
Brake caliper wrench
Return the piston
S-NT151
ZZC1313D
NNFIA0040ZZ
B
R
- 6
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005986561
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
,
,
,
,
,
NV
H
in
F
A
X
, R
A
X
a
n
d
FS
U,
R
S
U
s
e
c
tio
n
NV
H
in
WT s
e
cti
o
n
NV
H
in
WT s
e
cti
o
n
NV
H
in
F
A
X
se
ct
ion
NV
H
in
S
T
s
e
c
ti
o
n
Possible cause and
SUSPECTED PARTS
P
a
d
s
o
r li
ni
ng
da
ma
ge
d
P
a
d
s
o
r li
ni
ng
un
ev
en
wea
r
S
h
im
s
da
ma
ge
d
Ro
to
r im
ba
lan
c
e
Ro
to
r or
drum
d
a
m
a
g
e
Rotor runout
Ro
to
r de
form
a
tio
n
Ro
to
r or
drum
d
e
fl
ec
tio
n
Ro
to
r or
drum
ru
st
Ro
to
r th
ickne
s
s vari
ati
o
n
Dru
m
ou
t o
f ro
und
A
X
LE AND
SUSPENSI
ON
TI
RE
ROAD W
H
EEL
DRIV
E
SHAFT
S
T
EERING
Symptom
BRAKE
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
×
×
BRAKE PEDAL
BR-7
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment
INFOID:0000000005986567
INSPECTION
Brake Pedal Height
Check the height (H
1
) between the dash lower panel (1) and the
brake pedal upper surface.
CAUTION:
Remove the floor trim.
Stop Lamp Switch
Check the clearance (C) among the brake pedal lever (1) and the
stop lamp switch (2) threaded end.
CAUTION:
The stop lamp must turn off when the brake pedal is released.
NOTE:
Pull the brake pedal pad to make the clearance between the stop
lamp switch threaded end and the brake peal lever.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A) (stroke until
fluid pressure occurs).
Depressed Brake Pedal Height
Check the height between the dash lower panel (1) and the brake
pedal upper surface (H
2
) when depressing the brake pedal at 490 N
(50 kg, 110 lb) while turning engine ON.
CAUTION:
Remove the floor trim.
ADJUSTMENT
H
1
: Refer to
JPFIA0065ZZ
C
: Refer to
.
PFIA0813J
A
: Refer to
JPFIA0277ZZ
H
2
: Refer to
JPFIA0068ZZ
BR-8
< PERIODIC MAINTENANCE >
BRAKE PEDAL
Brake Pedal Height
1.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
2.
Disconnect the harness connector from stop lamp switch.
3.
Loosen the stop lamp switch 45
°
counterclockwise.
4.
Adjust the brake pedal height with the following procedure.
a.
Loosen the input rod lock nut (1).
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
b.
Rotate the input rod, adjust the brake pedal to the specified
height (H
1
).
c.
Tighten the lock nut. Refer to
.
5.
Check the brake pedal play.
Brake Pedal Play
NOTE:
The clearance between the stop lamp switch threaded end and the brake pedal lever is adjusted by adjusting
play of the brake pedal.
1.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
2.
Disconnect the harness connector from stop lamp switch.
3.
Loosen the stop lamp switch 45
°
counterclockwise.
4.
Press-fit the stop lamp switch (2) until the stop lamp switch hits
the brake pedal lever (1) 45
°
clockwise while pulling the brake
pedal pad slightly.
CAUTION:
• The clearance (C) between the brake pedal lever and stop
lamp switch threaded and must be the specified value.
• The stop lamp must be turned off when the brake pedal is
released.
JPFIA0003ZZ
H
1
: Refer to
.
JPFIA0279ZZ
C
: Refer to
.
PFIA0813J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст