Nissan March K13. Manual — part 453
MA-18
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
CAUTION:
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000005943112
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2.
Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Refer to
XX-XX, "*****"
.
Spark plug (Standard type)
: Refer to
Cleaner air pressure
: Less than 588 kPa (6 kg/cm
2
,
85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
CHASSIS MAINTENANCE
MA-19
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
CHASSIS MAINTENANCE
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000006057353
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
CLUTCH FLUID
CLUTCH FLUID : Inspection
INFOID:0000000006057355
FLUID LEAKAGE
• Check clutch line for cracks, deterioration or other damage. Replace any damaged parts.
• Check for fluid leakage by fully depressing clutch pedal while engine is running.
CAUTION:
If leakage occurs around joints, reinstall the joints or, if necessary, replace damaged parts.
FLUID LEVEL
• Check that the fluid level in the reservoir tank is within the specified
range (MAX – MIN lines).
• Visually check for any clutch fluid leakage around the reservoir
tank.
• Check the clutch system for any leakage if the fluid level is
extremely low (lower than MIN).
CLUTCH FLUID : Draining
INFOID:0000000006057356
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1.
Connect a transparent vinyl hose to air bleeder of bleeding con-
nector (1).
SMA211A
JPFIA0007ZZ
JPDIB0144ZZ
MA-20
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
2.
Press the lock pin (1) into the bleeding connector (2), and main-
tain the position.
3.
Slide clutch tube (1) in the direction of the arrow as shown in the
figure.
4.
Depress clutch pedal to gradually discharge clutch fluid.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
CLUTCH FLUID : Refilling
INFOID:0000000006057357
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1.
Check that there is no foreign material in reservoir tank and then fill with new clutch fluid.
CAUTION:
Never reuse drained clutch fluid.
2.
Connect a transparent vinyl hose to air bleeder of bleeding con-
nector (1).
3.
Press the lock pin (1) into the bleeding connector (2), and main-
tain the position.
PCIB1495E
2
: Bleeding connector
Dimension “A”
: 5 mm (0.20 in)
JPDIB0147ZZ
JPDIB0144ZZ
PCIB1495E
CHASSIS MAINTENANCE
MA-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
4.
Slide clutch tube (1) in the direction of the arrow as shown in the
figure.
5.
Slowly depress clutch pedal to the full stroke position and then
release the pedal.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
6.
Repeat step 5 at intervals of 2 or 3 seconds until new clutch fluid is discharged.
CAUTION:
Monitor clutch fluid level in reservoir tank so as not to empty the tank.
7.
Return clutch tube and lock pin in their original positions while clutch pedal is depressed.
8.
Perform the air bleeding. Refer to
CL-9, "Air Bleeding Procedure"
GEAR OIL
GEAR OIL : Inspection
INFOID:0000000006057364
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
1.
Remove filler plug (1) and gasket from transaxle case.
2.
Check the oil level from filler plug mounting hole as shown in the
figure.
CAUTION:
Never start engine while checking oil level.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
GEAR OIL : Draining
INFOID:0000000006057365
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.
3.
Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
2
: Bleeding connector
Dimension “A”
: 5 mm (0.20 in)
JPDIB0147ZZ
SCIA7119E
PCIB1504E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст