Nissan March K13. Manual — part 537
PG-136
< BASIC INSPECTION >
BATTERY INSPECTION
3.
Read load tester voltage when specified discharging current flows through battery for 15 seconds.
Is the voltage 9.6 V or more?
YES
>> Ready for use.
NO
>> Replace battery.
50D23L/R
150
55D23L/R
180
80D23L/R
195
65D26L/R
80D26L/R
75D31L/R
210
95D31L/R
240
115D31L/R
025 [YUASA type code]
027 [YUASA type code]
285
110D26L/R
300
95E41L/R
067 [YUASA type code]
325
130E41L/R
330
096 [YUASA type code]
375
Type
Current (A)
PG
FUSE INSPECTION
PG-137
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUSE INSPECTION
How To Check
INFOID:0000000005911876
• If fuse is blown, be sure to eliminate cause of malfunction before
installing new fuse.
• Use fuse of specified rating. Never use fuse of more than specified
rating.
• Do not partially install fuse; always insert it into fuse holder prop-
erly.
• Remove fuse for “ELECTRICAL PARTS (BAT)” if vehicle is not
used for a long period of time.
CEL083
PG-138
< BASIC INSPECTION >
FUSIBLE LINK INSPECTION
FUSIBLE LINK INSPECTION
How To Check
INFOID:0000000005911877
A melted fusible link can be detected either by visual inspection or by feeling with finger tip. If its condition is
questionable, use circuit tester or test lamp.
CAUTION:
• If fusible link should melt, it is possible that critical circuit (power supply or large current carrying
circuit) is shorted. In such a case, carefully check and eliminate cause of malfunction.
• Never wrap outside of fusible link with vinyl tape. Important: Never let fusible link touch any other
wiring harness, vinyl or rubber parts.
1.
Fusible link
JSMIA0234ZZ
PG
BATTERY CHARGING CHART
PG-139
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BATTERY CHARGING CHART
Slow Charge
INFOID:0000000005911878
1.
DETERMINE INITIAL CHARGING CURRENT
1.
Determine initial charging current from specific gravity.
2.
Check battery type and determine the specified current using the table.
NOTE:
After starting charging, adjustment of charging current is not necessary.
Initial Charging Current Setting (Slow Charge)
>> GO TO 2.
2.
CHARGE BATTERY
1.
Charge battery.
2.
Check charge voltage 30 minutes after starting the battery charge.
Is the voltage between 12 V and 15 V?
YES
>> GO TO 3.
NO
>> Replace battery.
3.
CHARGE BATTERY
Continue to charge for 12 hours.
>> GO TO 4.
4.
CHECKING SPECIFIC GRAVITY
Check specific gravity. Refer to
PG-130, "How to Handle Battery"
Is the specific gravity 1.240 or more?
YES
>> Complete slow charge. Perform “CAPACITY TEST”. Refer to
NO
>> GO TO 5.
5.
CONDUCT ADDITIONAL CHARGE
Add charging time depending on specific gravity.
Additional Charge (Slow Charge)
>> Complete slow charge. Perform “CAPACITY TEST”. Refer to
CAUTION:
• Set charging current to value specified in “Initial Charging Current Setting (Slow Charge)”. If charger
is not capable of producing specified current value, set its charging current as close to that value as
possible.
CONVERTED
SPECIFIC
GRAVITY
BATTERY TYPE
28
B1
9L
/R
34
B1
9L
/R
46
B2
4L
/R
55
B2
4L
/R
50
D2
3L
/R
55
D2
3L
/R
0
2
5
[YUAS
A
type
cod
e
]
0
2
7
[YUAS
A
type
cod
e
]
80
D2
3L
/R
65
D2
6L
/R
80
D2
6L
/R
0
6
7
[YUAS
A
type
cod
e
]
0
9
6
[YUAS
A
type
cod
e
]
75
D3
1L
/R
95
D3
1L
/R
1
1
5D31
L/
R
1
1
0D26
L/
R
95
E4
1L
/R
13
0E4
1
L
/R
Below 1.100
4.0 (A)
5.0 (A)
7.0 (A)
8.0 (A)
8.5
(A)
9.0
(A)
10.0 (A)
14.0
(A)
SPECIFIC GRAVITY
CHARGING TIME (h)
Below 1.150
5
1.150 - 1.200
4
1.200 - 1.240
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст