Nissan March K13. Manual — part 555
REAR SHOCK ABSORBER
RSU-7
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REMOVAL AND INSTALLATION
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000006044853
Removal and Installation
INFOID:0000000006044854
REMOVAL
1.
Remove tires. Refer to
XX-XX, "*****"
.
2.
Set suitable jack under rear suspension beam.
CAUTION:
Check the stable condition when using a jack.
3.
Remove shock absorber mounting bolt (lower side).
4.
Remove luggage lid from luggage side finisher. Refer to
XX-XX,
"*****"
.
5.
Remove cap and shock absorber mounting nut (upper side),
and then remove washer and bushing.
6.
Remove shock absorber assembly.
7.
Remove bushing, distance tube, bound bumper cover, and
bound bumper from shock absorber.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bushing), under unladen
conditions with tires on level ground.
1.
Cap
2.
Piston rod lock nut
3.
Washer
4.
Bushing
5.
Distance tube
6.
Bound bumper cover
7.
Bound bumper
8.
Shock absorber
9.
Rear suspension beam
Refer to
XX-XX, "*****"
for symbols in the figure.
JPEIB0222GB
JPEIB0176ZZ
RSU-8
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
• Install projection surely into the hole on the vehicle side as shown
in the figure, when installing bushing.
• Hold a head of shock absorber piston rod not to have it rotate, then
tighten piston rod lock nut with a standard tightening torque value.
Inspection
INFOID:0000000006044855
INSPECTION AFTER REMOVAL
Shock Absorber
Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
Bound Bumper, Bushing
Check for cracks and damage. Replace it if necessary.
Washer, Bound Bumper Cover, Distance Tube
• Check for cracks and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
XX-XX, "*****"
.
Disposal
INFOID:0000000006044856
1.
Set shock absorber horizontally to the ground with the piston rod fully extracted.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glass).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
JPEIB0171ZZ
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
COIL SPRING
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COIL SPRING
Exploded View
INFOID:0000000006044857
Removal and Installation
INFOID:0000000006044858
REMOVAL
1.
Remove tires. Refer to
XX-XX, "*****"
.
2.
Set jack under rear suspension beam.
CAUTION:
Check the stable condition when using a jack.
3.
Remove right and left rear shock absorber mounting bolts (lower side). Refer to
.
4.
Slowly lower jack, then remove upper rubber seat, coil spring and lower rubber seat from rear suspension
beam.
CAUTION:
Check the stable condition when using a jack.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the lower rubber seat a projection (A) is attached as rear
suspension beam mounting hole (B).
• Match up lower rubber seat indentions and rear suspension beam
grooves and attach.
Inspection
INFOID:0000000006044859
INSPECTION AFTER REMOVAL
Check lubber seat and coil spring for deformation, crack, and damage. Replace it if necessary.
1.
Upper rubber seat
2.
Coil spring
3.
Lower rubber seat
4.
Rear suspension beam
JPEIB0162ZZ
JPEIB0223ZZ
RSU-10
< REMOVAL AND INSTALLATION >
COIL SPRING
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
XX-XX, "*****"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст