Nissan March K13. Manual — part 627
ST-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000006038905
Commercial Service Tools
INFOID:0000000006038906
Tool number
Tool name
Description
ST3127S000
Preload gauge
Inspecting steering column assembly rotating
torque, pinion rotating torque and ball joint ro-
tating torque
ST27180001
Steering wheel puller
Removing steering wheel
KV48103400
Preload adapter
Inspecting rotating torque
ZZA0806D
ZZA0819D
ZZA0824D
Tool name
Description
Ball joint remover
Remove steering outer socket
Boot band crimping tool
Installing boot clamp (large diameter)
S-NT146
ZZA1229D
STEERING WHEEL
ST-5
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
BASIC INSPECTION
STEERING WHEEL
Inspection
INFOID:0000000006038907
NEUTRAL POSITION STEERING WHEEL
1.
Make sure that steering gear assembly, steering column assembly and steering wheel are installed in the
correct position.
2.
Perform neutral position inspection after wheel alignment. Refer to
3.
Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.
4.
Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.
STEERING WHEEL TURNING FORCE
1.
Park vehicle on a level and dry surface, set parking brake.
2.
Tires need to be inflated normal pressure. Refer to
.
3.
Start engine.
4.
Check steering wheel turning force when steering wheel has
been turned 360
°
from neutral position.
NOTE:
Multiply the distance (L) from the hook of spring balance to the
center of steering wheel by the measurement value with a spring
balance.
FRONT WHEEL TURNING ANGLE
1.
Check front wheel turning angle after toe-in inspection. Refer to
2.
Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.
3.
Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.
4.
With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
Steering wheel turning
force
: Refer to
SGIA1523J
FAA0016D
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
ST-6
< BASIC INSPECTION >
STEERING WHEEL
5.
Check the following items when turning angle is out of the stan-
dard.
a.
Check rack stroke (L).
b.
Disassemble steering gear assembly to check the cause that
rack stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear
assembly, steering column assembly and front suspension
components for wear or damage if any of the turning angles
are different from the specified value. Replace any of them, if
any non-standard condition exists.
L
: Refer to
.
JSGIA0272ZZ
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
ST-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000006038908
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
NVH in F
AX, RAX
, FSU, RSU section
NVH in WT
se
ct
io
n
NVH in WT
se
ct
io
n
NVH in F
AX section
NVH in BR section
Possible cause and SUSPECTED PARTS
Oute
r/in
ne
r s
o
c
k
e
t b
a
ll jo
in
t s
w
ing
in
g
t
o
rq
ue
Oute
r/in
ne
r socke
t b
a
ll jo
in
t ro
ta
ti
ng
to
rqu
e
Oute
r/in
ne
r s
o
c
k
e
t b
a
ll jo
in
t e
n
d
pl
ay
S
te
e
ri
ng
whe
e
l pl
ay
Im
prop
er st
eeri
n
g
whe
e
l
Im
prop
er
in
st
a
lla
ti
on
or l
o
o
s
e
n
e
s
s
o
f ti
lt
loc
k
le
ve
r
M
o
u
n
ti
ng
l
o
os
en
es
s
S
tee
rin
g
c
o
lu
m
n
d
e
fo
rm
at
io
n
or da
ma
ge
Im
prop
er
in
st
a
lla
ti
on
or l
o
o
s
e
n
e
s
s
o
f s
tee
rin
g
c
o
lu
m
n
S
tee
rin
g
l
in
ka
ge
lo
os
en
es
s
AXLE
and
SUSPENSION
TIRE
ROA
D
WHEEL
DRIVE SHA
F
T
BRAKE
Symptom
Steering
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст