Nissan March K13. Manual — part 21
BCS
BCM
BCS-57
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REMOVAL AND INSTALLATION
BCM
Removal and Installation
INFOID:0000000006014865
CAUTION:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specifica-
tion. Refer to
.
REMOVAL
1.
Remove glove box cover. Refer to
2.
Remove screws.
3.
Disconnect BCM connector.
4.
Remove door mirror open relay, door mirror close relay and rear window defogger relay from bracket.
5.
Remove relay mounting bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Be sure to perform “WRITE CONFIGURATION” when replacing BCM.
• Be sure to perform the system initialization (NATS) when replacing BCM. Refer to
.
BCS-58
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
COMBINATION SWITCH
COMBINATION SWITCH
Exploded View
INFOID:0000000006046466
Removal and Installation
INFOID:0000000006014866
REMOVAL
1.
Remove steering column cover. Refer to
.
2.
Remove screws.
3.
Disconnect the connector.
4.
Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1.
Combination switch
2.
Combination switch connector
JMMIA0383ZZ
BCS
PRECAUTIONS
BCS-59
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006014867
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
BCS-60
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM : Component Parts Location
INFOID:0000000006046472
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM : Component Parts Location
INFOID:0000000006046473
1.
BCM
A.
Left side of glove box
JMMIA0390ZZ
1.
IPDM E/R
Refer to
.
2.
Combination meter
3.
SYSTEM : Component Parts Loca-
tion"
JMMIA0391ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст