Nissan March K13. Manual — part 103
REAR DOOR
DLK-123
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
8.
Install center pillar garnish (lower). Refer to
INT-23, "CENTER PILLAR LOWER GARNISH : Removal and
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000005948988
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000005948990
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-121, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove center pillar lower garnish. Refer to
INT-23, "CENTER PILLAR LOWER GARNISH : Removal
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check rear door open/close operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000005948992
REMOVAL
1.
Fully close the rear door window.
2.
Remove rear door finisher. Refer to
INT-18, "Removal and Installation"
.
3.
Remove sealing screen (lower). (Without door speaker)
4.
Remove rear door speaker mounting bolts.
5.
Disconnect connector and remove rear door speaker.
DLK-124
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
6.
Remove mounting bolts of the check link on the vehicle.
7.
Remove mounting bolts of the check link on door panel.
8.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check rear door open/close operation after installation.
BACK DOOR
DLK-125
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Exploded View
INFOID:0000000006054230
REMOVAL
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000006054231
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Remove high-mounted stop lamp. Refer to
EXL-101, "Removal and Installation"
2.
Remove grommet (2), and then disconnect washer tube (A).
3.
Remove grommet (3), and then pull out washer tube from back
door assembly (1).
1.
Back door weather-strip
2.
Back door stay
3.
Stud ball
4.
Bumper rubber
5.
Back door striker
6.
Back door assembly
7.
Back door hinge
A
: Center mark
Refer to
JMKIA5325GB
JMKIA5327ZZ
DLK-126
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
4.
Disconnect rear window defogger connector (LH), and then remove terminal from connector.
5.
Remove back door finisher. Refer to
INT-33, "Removal and Installation"
.
6.
Remove ground mounting bolt (A).
7.
Disconnect connectors of back door harness.
8.
Remove harness grommet (1), and then pull out harness from
back door assembly (2).
9.
Support back door lock with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
10. Remove back door stay (back door side). Refer to
DLK-129, "BACK DOOR STAY : Removal and Installa-
11. Remove back door hinge mounting bolts on back door and remove back door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to
DLK-127, "BACK DOOR ASSEMBLY :
JMKIA5328ZZ
JMKIA5329ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст