Nissan Murano Z51 (2012 year). Manual — part 29
![](/vehicles/gon/quras/ong/ienoveriyero.png)
FRONT DRIVE SHAFT
FAX-43
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Exploded View
INFOID:0000000007541227
LEFT SIDE
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Circular clip
7.
Joint sub-assembly
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
Refer to
for symbols not described on the above.
JPDIF0243ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band
6.
Dynamic damper
7.
Housing assembly
8.
Circular clip
9.
Dust shield
10. Oil seal
11.
Bearing housing
12. Bearing bracket
JPDIF0241GB
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/bbecheske.png)
FAX-44
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
LEFT SIDE
LEFT SIDE : Removal and Installation
INFOID:0000000007541228
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-121, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-21, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-38, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and
.
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, housing assembly
and the other parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove strut assembly from steering knuckle. Refer to
.
10. Remove drive shaft from transaxle assembly.
• Use the drive shaft attachment (A) [SST: KV40107500 (
—
)] and a sliding hammer (B) while inserting tip of the drive
shaft attachment between housing assembly and transaxle
assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
• Confirm that the circular clip is attached to the drive
shaft.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
.
13. Snap ling
14. Dust shield
15. collor
16. Link shaft
17. Support bearing bracket
A:
Oil seal lip
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
3: Appy multi - purpose grease.
Refer to
for symbols not described on the above.
JPDIF0004ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/panoug.png)
FRONT DRIVE SHAFT
FAX-45
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Place the protector (A) [SST: KV38107900 (
—
)] onto transaxle
assembly to prevent damage to the oil seal while inserting drive
shaft. Slide drive shaft sliding joint and tap with a hammer to install
securely.
CAUTION:
Make sure that circular clip is completely engaged.
• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub and bearing assembly.
CAUTION:
Apply paste [service parts (440037S000)] to cover entire flat
surface (A) of joint sub-assembly of drive shaft.
• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen condi-
tions, which were removed when removing wheel hub and bearing
assembly and axle housing.
• Never reuse cotter pin.
RIGHT SIDE
RIGHT SIDE : Removal and Installation
INFOID:0000000007541229
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-121, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-21, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-38, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and
.
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, housing assembly
and the other parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove strut assembly from steering knuckle. Refer to
.
10. Remove drive shaft from wheel hub and bearing assembly.
JPDIF0023ZZ
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIG0122ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/the.png)
FAX-46
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
11. Remove drive shaft from link shaft.
• Use the drive shaft attachment (A) [SST: KV40107500 (
—
)] and a sliding hammer (B) while inserting tip of the drive
shaft attachment between housing assembly and link shaft
assembly.
CAUTION:
Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
12. Remove bearing housing mounting bolts.
13. Remove link shaft assembly from support bearing bracket.
14. Remove support bearing bracket, follow the procedure
described below.
a.
Remove front exhaust tube. Refer to
b.
Remove three way catalyst (bank 1) and heated oxygen sensor harness bracket. Refer to
c.
Remove support bearing bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Always replace differential side oil seal with new one when installing link shaft. Refer to
.
• Place the protector (A) [SST: KV38107900 (
—
)] onto transaxle
assembly to prevent damage to the oil seal while inserting lonk
shaft. Slide link shaft sliding joint and tap with a hammer to install
securely.
• Install support bearing bracket (1) in following procedure,
- Temporarily tighten mounting bolts (A), then tighten them to speci-
fied torque.
- Temporarily tighten mounting bolts (B), then tighten them to speci-
fied torque.
• Apply NISSAN genuine grease to drive shaft serration (link shaft side), and install drive shaft onto link shaft.
• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub and bearing assembly.
CAUTION:
JPDIF0004ZZ
JPDIF0147ZZ
JPDIF0143ZZ
Standard
: 1.5 – 2.5 g (0.053 – 0.088 oz)
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/heyo.png)
FRONT DRIVE SHAFT
FAX-47
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Apply paste [service parts (440037S000)] to cover entire flat
surface (A) of joint sub-assembly of drive shaft.
• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen condi-
tions, which were removed when removing wheel hub and bearing
assembly and axle housing.
• Never reuse cotter pin.
WHEEL SIDE
WHEEL SIDE : Disassembly and Assembly
INFOID:0000000007541230
DISASSEMBLY
1.
Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Remove boot bands, and then remove boot from joint sub-assembly.
3.
Screw drive shaft puller (A) into joint sub-assembly screw part to
a length of 30 mm (1.18 in) or more. Support drive shaft with one
hand and pull out joint sub-assembly with a sliding hammer (B)
from housing assembly.
CAUTION:
• Align a sliding hammer and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle.
4.
Remove circular clip (1) from housing assembly.
5.
Remove boot from housing assembly.
ASSEMBLY
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent until the serration slot and
ball groove become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old grease that has oozed out.
3.
Install boot and boot bands to housing assembly.
CAUTION:
• Wrap serration on housing assembly with tape to protect the boot from damage.
• Never reuse boot and boot band.
4.
Remove the tape wrapped around the serration on housing assembly.
5.
Position the circular clip on groove at the housing assembly edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6.
Align both center axles of the housing assembly edge and joint sub-assembly. Then assemble housing
assembly with circular clip joint sub-assembly.
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIG0122ZZ
JPDIF0015ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/rers.png)
FAX-48
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
7.
Install joint sub-assembly to housing assembly using plastic
hammer.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive housing assembly.
8.
Apply the specified amount of grease into the boot inside from
large diameter side of boot.
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the housing assembly or joint sub-assem-
bly, boot may be removed. Remove all grease from the boot
mounting surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into inside of the boot from the large diameter
side of the boot and discharging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST: KV40107300 (
—
)].
CAUTION:
Never reuse boot band.
NOTE:
Secure boot band so that dimension (A) meets the specification
as shown in the figure.
12. Secure joint sub-assembly and housing assembly, and then
make sure that they are in the correct position when rotating
boot. Reinstall them using boot bands when boot installation
positions become incorrect.
CAUTION:
Never reuse boot band.
TRANSAXLE SIDE
TRANSAXLE SIDE : Disassembly and Assembly
INFOID:0000000007541231
DISASSEMBLY
Grease amount
: Refer to
.
RAC0049D
L
: Refer to
.
JPDIF0222ZZ
JPDIF0012ZZ
A
: 7.0 mm (0.276 in) or less
JPDIF0268ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/cameringt.png)
FRONT DRIVE SHAFT
FAX-49
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Left Side
1.
Fix drive shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Disassemble boot (wheel side). Refer to
FAX-47, "WHEEL SIDE : Disassembly and Assembly"
3.
Remove boot bands and boot (transaxle side).
Right Side
1.
Fix drive shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Disassemble boot (wheel side). Refer to
FAX-47, "WHEEL SIDE : Disassembly and Assembly"
3.
Remove dynamic damper, follow the procedure described below.
a.
Remove damper bands.
b.
Remove dynamic damper from shaft.
4.
Remove boot bands and boot (transaxle side).
5.
Remove dust shield from housing assembly.
6.
Remove support bearing from link shaft, follow the procedure described below.
a.
Press out bearing housing and support bearing from link shaft.
b.
Remove dust shield from bearing housing.
c.
Remove snap ring (1).
d.
Remove oil seal.
e.
Press out support bearing from bearing housing (1) with drift (A)
[SST: ST17130000 (
—
)]
ASSEMBLY
Left Side
1.
Install dust shield.
CAUTION:
Never reuse dust shield.
2.
Install circular clip.
CAUTION:
Never reuse circular clip.
3.
Clean old grease on housing assembly with paper waste.
JPDIF0177ZZ
JPDIF0192ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/hescopli.png)
FAX-50
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
4.
Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on housing assembly, boot may be removed.
Remove all grease from the boot mounting surface.
5.
To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into the inside of boot from the large diameter
side of boot and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with the tip of tool.
6.
Install boot bands securely as shown in the figure.
a.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b.
Pinch projection on the band with suitable pliers to tighten band.
c.
Insert tip of band below end of the pawl.
7.
Secure housing assembly, and then make sure that they are in
the correct position when rotating boot. Reinstall them with boot
bands when the mounting positions become incorrect.
Right Side
1.
Install support bearing from link shaft, follow the procedure described below.
a.
Press support bearing to bearing housing (1) with drift (A) [SST:
ST35271000 (
—
)]
L
: Refer to
JPDIF0144ZZ
JPDIF0157ZZ
JPDIF0158ZZ
JPDIF0192ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/tam.png)
FRONT DRIVE SHAFT
FAX-51
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
b.
Install snap ring (1).
CAUTION:
Never reuse snap ring.
c.
Install dust shield to baring housing.
CAUTION:
Never reuse dust shield.
d.
Install oil seal to bearing housing with drift.
CAUTION:
• Never reuse oil seal.
• Apply multi - purpose grease to oil seal lip.
e.
Press bearing housing assembly to link shaft.
f.
Install circular clip to link shaft.
CAUTION:
Never reuse circular clip.
2.
Clean old grease on housing assembly with paper waste.
3.
Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on housing assembly, boot may be removed.
Remove all grease from the boot mounting surface.
4.
To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into the inside of boot from the large diameter
side of boot and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with the tip of tool.
5.
Install boot bands securely as shown in the figure.
a.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b.
Pinch projection on the band with suitable pliers to tighten band.
c.
Insert tip of band below end of the pawl.
6.
Secure housing assembly, and then make sure that they are in
the correct position when rotating boot. Reinstall them with boot
bands when the mounting positions become incorrect.
7.
Assemble boot (wheel side) and joint sub-assembly. Refer to
FAX-47, "WHEEL SIDE : Disassembly and Assembly"
.
8.
Install dynamic damper, follow the procedure described below.
a.
Install dynamic damper to shaft.
L
: Refer to
.
JPDIF0177ZZ
JPDIF0144ZZ
JPDIF0157ZZ
JPDIF0158ZZ
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/merr.png)
FAX-52
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
b.
Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse bands.
Inspection
INFOID:0000000007541232
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if necessary.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing Assembly (Transaxle Side)
Replace housing assembly if there is scratching or wear of housing assembly roller contact surface.
Link Shaft (Right side)
Check shaft for runout, cracks, or other damage. Replace if necessary.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
A
: Refer to
JPDIF0178ZZ
SDIA1190J
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/ominaimestut.png)
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-53
< SERVICE DATA AND SPECIFICATIONS (SDS)
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000007541233
Drive Shaft
INFOID:0000000007541234
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Item
Standard
Left side
Right side
Grease quantity
Wheel side
170 – 190 g (6.00 – 6.70 oz)
Transaxle side
155 – 175 g (5.47 – 6.17 oz)
Boots installed length
Wheel side
158.6 mm (6.24 in)
Transaxle side
163.67 mm (6.44 in)
159.47 mm (6.28 in)
Dimension of dynamic damper
—
202 – 208 mm (7.95 – 8.19 in)
Revision: 2013 February
2012 MURANO
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
FOR USA AND CANADA . . . . . . . . . . ....
FOR USA AND CANADA : Precaution for Proce-
dure without Cowl Top Cover . . . . . . . . ....
FOR USA AND CANADA : Precautions for Sus-
pension . . . . . . . . . . . . . . . . . ..
FOR MEXICO . . . . . . . . . . . . . . . ..
FOR MEXICO : Precaution for Procedure without
Cowl Top Cover . . . . . . . . . . . . . ....
FOR MEXICO : Precautions for Suspension . . ....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . .
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
FRONT COIL SPRING AND STRUT . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
TRANSVERSE LINK . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT STABILIZER . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION . ..
FRONT SUSPENSION MEMBER . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
Wheelarch Height . . . . . . . . . . . . .
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/ghar.png)
FSU-2
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000007542077
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
,
,
,
—
—
,
,
,
NVH in DLN
section
NVH in DLN
section
NVH in
F
AX
and FS
U sections
NVH in
WT section
NVH in
WT section
NVH in F
A
X section
NVH in BR
section
NVH in ST
section
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
tal
la
tio
n
,
loo
s
ene
s
s
S
hoc
k
ab
so
rbe
r d
e
fo
rma
tio
n,
da
ma
ge
o
r de
fle
c
tion
B
u
s
h
in
g
or m
o
u
n
ting
d
e
te
rio
rati
o
n
P
a
rt
s interference
S
p
ri
ng
fat
ig
u
e
S
us
pe
ns
ion
lo
os
en
es
s
In
co
rrec
t wh
ee
l a
lig
nm
en
t
S
ta
b
iliz
er b
a
r f
a
ti
gu
e
PR
OP
EL
LE
R
S
H
A
F
T
(
A
W
D
)
DIFFERENTIAL (A
WD)
F
R
ONT
AXLE AND FRONT S
U
SPENSION
TI
RE
ROAD
WHEEL
DRIV
E SHAFT
BR
AK
E
S
T
EERING
Symptom
FRONT SUSPENSION
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/lakngrreah.png)
PRECAUTIONS
FSU-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000007542078
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR USA AND CANADA : Precaution for Procedure without Cowl Top Cover
INFOID:0000000007542080
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
FOR USA AND CANADA : Precautions for Suspension
INFOID:0000000007542081
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
PIIB3706J
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/ptlldd.png)
FSU-4
< PRECAUTION >
PRECAUTIONS
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000007542082
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000007542084
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
FOR MEXICO : Precautions for Suspension
INFOID:0000000007542085
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
PIIB3706J
Revision: 2013 February
2012 MURANO
![](/vehicles/gon/quras/ong/llereayoryo.png)
PREPARATION
FSU-5
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000007542086
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000007542087
Tool number
(Kent-More No.)
Tool name
Description
ST35652000
(
—
)
Strut attachment
Disassembling and assembling strut
ZZA0807D
Tool name
Description
Spring compressor
Removing and installing coil spring
Power tool
Loosening bolts and nuts
S-NT717
PBIC0190E
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст