Nissan Murano Z51 (2012 year). Manual — part 52
MIR-12
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-182, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch (mirror switch).
Refer to
MIR-12, "MIRROR SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (mirror switch). Refer to
.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-44, "Intermittent Incident"
>> INSPECTION END
MIRROR SWITCH : Component Inspection
INFOID:0000000007540662
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
D14
15
Existed
4
13
15
12
16
4
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Revision: 2013 February
2012 MURANO
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-13
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-49, "Removal and Installation"
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000007540663
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000007540664
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
MIR-13, "CHANGEOVER SWITCH : Diagnosis Procedure"
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000007540665
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
4
7
Mirror switch
RIGHT
Existed
Other than above
Not existed
13
LEFT
Existed
Other than above
Not existed
15
UP
Existed
Other than above
Not existed
12
DOWN
Existed
Other than above
Not existed
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
10
Ground
5
11
Revision: 2013 February
2012 MURANO
MIR-14
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-182, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to
MIR-14, "CHANGEOVER SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (changeover switch). Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-44, "Intermittent Incident"
>> INSPECTION END
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000007540666
1.
CHECK CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
2
D14
11
Existed
14
10
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
2
Not existed
14
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Revision: 2013 February
2012 MURANO
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-15
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-49, "Removal and Installation"
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
10
7
Changeover switch
LEFT
Existed
Other than above
Not existed
11
RIGHT
Existed
Other than above
Not existed
Revision: 2013 February
2012 MURANO
MIR-16
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR
DOOR MIRROR
Wiring Diagram - DOOR MIRROR SYSTEM (WITH AUTOMATIC DRIVE POSITION-
ER) -
INFOID:0000000007540667
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWM2736GB
Revision: 2013 February
2012 MURANO
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
MIR-17
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -
INFOID:0000000007540668
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWM6099GB
Revision: 2013 February
2012 MURANO
MIR-18
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
ECU DIAGNOSIS INFORMATION
DRIVER SEAT CONTROL UNIT
Reference Value
INFOID:0000000007687747
VALUES ON THE DIAGNOSIS TOOL
CONSULT MONITOR ITEM
Monitor Item
Condition
Value/Status
SET SW
Set switch
Push
ON
Release
OFF
MEMORY SW1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW2
Memory switch 2
Push
ON
Release
OFF
SLIDE SW–FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW–RR
Sliding switch (backward)
Operate
ON
Release
OFF
RECLN SW–FR
Reclining switch (forward)
Operate
ON
Release
OFF
RECLN SW–RR
Reclining switch (back-
ward)
Operate
ON
Release
OFF
LIFT FR SW–UP
Lifting switch front (up)
Operate
ON
Release
OFF
LIFT FR SW–DN
Lifting switch front (down)
Operate
ON
Release
OFF
LIFT RR SW–UP
Lifting switch rear (up)
Operate
ON
Release
OFF
LIFT RR SW–DN
Lifting switch rear (down)
Operate
ON
Release
OFF
MIR CON SW–UP
Mirror switch
Up
ON
Other than above
OFF
MIR CON SW–DN
Mirror switch
Down
ON
Other than above
OFF
MIR CON SW–RH
Mirror switch
Right
ON
Other than above
OFF
MIR CON SW–LH
Mirror switch
Left
ON
Other than above
OFF
MIR CHNG SW–R
Changeover switch
Right
ON
Other than above
OFF
MIR CHNG SW–L
Changeover switch
Left
ON
Other than above
OFF
TILT SW-UP
Tilt switch
Upward
ON
Other than above
OFF
TILT SW-DOWN
Tilt switch
Downward
ON
Other than above
OFF
Revision: 2013 February
2012 MURANO
DRIVER SEAT CONTROL UNIT
MIR-19
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
TELESCO SW-FR
Telescopic switch
Forward
ON
Other than above
OFF
TELESCO SW-RR
Telescopic switch
Backward
ON
Other than above
OFF
DETENT SW
Selector lever
P position
OFF
Other than above
ON
STARTER SW
Ignition position
Cranking
ON
Other than above
OFF
SLIDE PULSE
Seat sliding
Forward
The numeral value decreases *
Backward
The numeral value increases*
Other than above
No change to numeral value*
RECLN PULSE
Seat reclining
Forward
The numeral value decreases*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT FR PULSE
Seat lifter (front)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT RR PULSE
Seat lifter (rear)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
MIR/SEN RH U–D
Door mirror (passenger side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN RH R–L
Door mirror (passenger side)
Change between 3.4 (close to left edge)
0.6 (close to right edge)
MIR/SEN LH U–D
Door mirror (driver side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN LH R–L
Door mirror (driver side)
Change between 0.6 (close to left edge)
3.4 (close to right edge)
TILT PULSE
Tilt position
Upward
The numeral value decreases
*
Downward
The numeral value increases
*
Other than above
No change to numeral value
*
TELESCO PULSE
Telescopic position
Forward
The numeral value decreases
*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
STEERING STATUS
NOTE:
This item is displayed, but cannot be monitored
VEHICLE SPEED
The condition of vehicle speed is displayed
km/h
P RANG SW CAN
Selector lever
P position
ON
Other than above
OFF
R RANGE (CAN)
Selector lever
R position
ON
Other than above
OFF
DOOR SW-FL
Driver door
Open
ON
Close
OFF
Monitor Item
Condition
Value/Status
Revision: 2013 February
2012 MURANO
MIR-20
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
*
: The value at the position attained when the battery is connected is regarded as 32768.
TERMINAL LAYOUT
PHYSICAL VALUES
DOOR SW-FR
Passenger door
Open
ON
Close
OFF
IGN ON SW
Ignition switch
ON position
ON
Other than above
OFF
ACC ON SW
Ignition switch
ACC or ON position
ON
Other than above
OFF
KEY ON SW
Intelligent Key
Inserted is key slot
ON
Inserted is not key slot
OFF
KEYLESS ID
UNLOCK button of Intelligent Key is pressed
1,2,3,4or5
KYLS DR UNLK
Intelligent Key or driver
side door request switch
ON
ON
OFF
OFF
VHCL SPEED (ABS)
Can signal from ABS
Received
ON
Not received
OFF
HANDLE
The BCM for handle position is displayed
LHD
RHD
TRANSMISSION
Transmission type is displayed
AT or CVT
MT
Monitor Item
Condition
Value/Status
JMJIA1689ZZ
Terminal No.
(wire color)
Description
Condition
Voltage (V)
(Approx)
+
-
Signal name
Input/
Output
1
(R)
Ground
Power source
Input
—
Battery voltage
2
(B)
Ground
Ground (power)
—
—
0
3
(G)
Ground
Sliding motor backward
output signal
Output
Seat sliding
Operate
(backward)
Battery voltage
Stop
0
4
(G/R)
Ground
Sliding motor forward out-
put signal
Output
Seat sliding
Operate
(forward)
Battery voltage
Release
0
5
(V)
Ground
Reclining motor backward
output signal
Output
Seat reclining
Operate
(backward)
Battery voltage
Stop
0
Revision: 2013 February
2012 MURANO
DRIVER SEAT CONTROL UNIT
MIR-21
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
6
(R/L)
Ground
Reclining motor forward
output signal
Output
Seat reclining
Operate
(forward)
Battery voltage
Release
0
7
(L)
Ground
Lifting motor (rear) down
output signal
Output
Seat lifting (rear)
Operate
(down)
Battery voltage
Stop
0
8
(L/W)
Ground
Lifting motor (rear) up out-
put signal
Output
Seat lifting (rear)
Operate
(up)
Battery voltage
Stop
0
9
(L/R)
Ground
Lifting motor (front) down
output signal
Output
Seat lifting (front)
Operate
(down)
Battery voltage
Stop
0
10
(L/B)
Ground
Lifting motor (front) up out-
put signal
Output
Seat lifting (front)
Operate
(up)
Battery voltage
Stop
0
11
(G/B)
Ground
Sliding switch backward
signal
Input
Sliding switch
Operate
(backward)
0
Release
Battery voltage
12
(G/W)
Ground
Sliding switch forward sig-
nal
Input
Sliding switch
Operate
(forward)
0
Release
Battery voltage
13
(R/G)
Ground
Reclining switch backward
signal
Input
Reclining switch
Operate
(backward)
0
Release
Battery voltage
14
(R/W)
Ground
Reclining switch forward
signal
Input
Reclining switch
Operate
(forward)
0
Release
Battery voltage
15
(Y/B)
Ground
Lifting switch (rear) down
signal
Input
Lifting switch
(rear)
Operate
(down)
0
Release
Battery voltage
16
(Y/R)
Ground
Lifting switch (rear) up sig-
nal
Input
Seat lifting switch
(rear)
Operate
(up)
0
Release
Battery voltage
17
(LG/B)
Ground
Lifting switch (front) down
signal
Input
Lifting switch
(front)
Operate
(down)
0
Release
Battery voltage
18
(LG/R)
Ground
Lifting switch (front) up sig-
nal
Input
Seat lifting switch
(front)
Operate
(up)
0
Release
Battery voltage
19
(G/Y)
Ground
Sliding sensor signal
Input
Seat sliding
Operate
Stop
0 or 5
Terminal No.
(wire color)
Description
Condition
Voltage (V)
(Approx)
+
-
Signal name
Input/
Output
JMJIA0119ZZ
Revision: 2013 February
2012 MURANO
MIR-22
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
20
(R/Y)
Ground
Reclining sensor signal
Input
Seat reclining
Operate
Stop
0 or 5
21
(L/Y)
Ground
Lifting sensor (rear) signal
Input
Seat lifting (rear)
Operate
Stop
0 or 5
22
(BR/Y)
Ground
Lifting sensor (front) signal
Input
Seat lifting (front)
Operate
Stop
0 or 5
23
(P)
—
CAN-H
—
—
—
24
(P/L)
—
CAN-L
—
—
—
25
(G/O)
Ground
Memory indictor 1 signal
Output
Memory indictor 1
Illuminate
1
Other than above
Battery voltage
26
(L/O)
Ground
Memory indictor 2 signal
Output
Memory indictor 2
Illuminate
1
Other than above
Battery voltage
27
(V)
Ground
Memory switch 1 signal
Input
Memory switch 1
Press
0
Other than above
5
28
(V/W)
Ground
Memory switch 2 signal
Input
Memory switch 2
Press
0
Other than above
5
29
(O/L)
Ground
Set switch signal
Input
Set switch
Press
0
Other than above
5
30
(BR)
Ground
Tilt sensor signal
Input
Tilt
Operate
Other than above
0 or 5
Terminal No.
(wire color)
Description
Condition
Voltage (V)
(Approx)
+
-
Signal name
Input/
Output
JMJIA0119ZZ
JMJIA0119ZZ
JMJIA0119ZZ
JMJIA0119ZZ
Revision: 2013 February
2012 MURANO
DRIVER SEAT CONTROL UNIT
MIR-23
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
31
(BR/W)
Ground
Telescopic sensor signal
Input
Telescopic
Operate
Other than above
0 or 5
32
(W/L)
Ground
UART communication
(TX/RX)
Input
Ignition switch ON
33
(W)
Ground
Sensor power supply
Output
—
Battery voltage
Terminal No.
(wire color)
Description
Condition
Voltage (V)
(Approx)
+
-
Signal name
Input/
Output
JMJIA1391ZZ
Revision: 2013 February
2012 MURANO
MIR-24
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
Wiring Diagram - AUTOMATIC DRIVE POSITIONER CONTROL SYSTEM -
INFOID:0000000007687748
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRJWC0297GB
Revision: 2013 February
2012 MURANO
DRIVER SEAT CONTROL UNIT
MIR-25
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
JRJWC0298GB
Revision: 2013 February
2012 MURANO
MIR-26
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
Fail Safe
INFOID:0000000007687749
The fail-safe mode may be activated if the following symptoms are observed.
JRJWC0299GB
Revision: 2013 February
2012 MURANO
DRIVER SEAT CONTROL UNIT
MIR-27
< ECU DIAGNOSIS INFORMATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DTC Index
INFOID:0000000007687750
*1
:
• 0: Current malfunction is present
• 1-39: Displayed if any previous malfunction is present when current condition is normal. The numeral value increases by one at each
IGN ON to OFF cycle from 1 to 39. The counter remains at 39 even if the number of cycles exceeds it. However, the counter is reset
to 1 if any malfunction is detected again, the normal operation is resumed and the ignition switch is turned from OFF to ON.
Operating in
fail-safe mode
Malfunction Item
Related
DTC
Diagnosis
Only manual functions operate normally.
CAN communication
U1000
CONTROL UNIT
U1010
EEPROM
B2130
Only manual functions, except door mirror, operate normally.
UART communication
B2128
Only manual functions, except seat sliding, operate normally.
Seat sliding output
B2112
Only manual functions, except seat reclining, operate normally.
Seat reclining output
B2113
Only manual functions, except steering tilt, operate normally.
Steering column tilt output
B2116
CONSULT
display
Timing
*1
Item
Reference page
Current mal-
function
Previous mal-
function
CAN COMM CIRCUIT
[U1000]
0
1-39
CAN communication
CONTROL UNIT
[U1010]
0
1-39
Control unit
SEAT SLIDE
[B2112]
0
1-39
Seat slide motor output
SEAT RECLINING
[B2113]
0
1-39
Seat reclining motor output
STEERING TILT
[B2116]
0
1-39
Tilt motor output
UART COMM
[B2128]
0
1-39
UART communication
EEPROM
[B2130]
0
1-39
EEPROM
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст