Nissan Murano Z51 (2012 year). Manual — part 74
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-
LY
PWC-83
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES
NORMALLY
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000007541392
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ENCODER (DRIVER SIDE) CIRCUIT
Check encoder (driver side) circuit.
Refer to
PWC-27, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000007541393
1.
PERFORM INITIALIZAITON PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ENCODER (PASSENGER SIDE) CIRCUIT
Check encoder (passenger side) circuit.
Refer to
PWC-29, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
PWC-84
< SYMPTOM DIAGNOSIS >
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000007541394
1.
CHECK POWER WINDOW AUTO OPERATION
Check power window auto operation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-83, "DRIVER SIDE : Diagnosis Procedure"
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000007541395
1.
CHECK POWER WINDOW AUTO OPERATION
Check power window auto operation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-83, "PASSENGER SIDE : Diagnosis Procedure"
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
PWC-85
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY
Diagnosis Procedure
INFOID:0000000007541396
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-97, "WITH AUTOMATIC BACK DOOR : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
PWC-86
< SYMPTOM DIAGNOSIS >
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WINDOWS
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WIN-
DOWS
Diagnosis Procedure
INFOID:0000000007541397
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK DRIVER SIDE DOOR LOCK ASSEMBLY (DOOR KEY CYLINDER SWITCH)
Check driver side door lock assembly (door key cylinder switch).
Refer to
DLK-110, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
PWC-87
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000007541398
1.
CHECK INTELLIGENT KEY FUNCTION
Check Intelligent Key function.
Refer to
DLK-127, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace BCM. Refer to
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
PWC-88
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000007541399
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
>> Refer to
PWC-92, "Removal and Installation"
Revision: 2013 February
2012 MURANO
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
PWC-89
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
Diagnosis Procedure
INFOID:0000000007541400
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
>> Refer to
PWC-92, "Removal and Installation"
Revision: 2013 February
2012 MURANO
PWC-90
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000007814590
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR USA AND CANADA : Precaution for Procedure without Cowl Top Cover
INFOID:0000000007814592
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000007814591
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
PIIB3706J
Revision: 2013 February
2012 MURANO
PRECAUTIONS
PWC-91
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000007814593
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 February
2012 MURANO
PWC-92
< REMOVAL AND INSTALLATION >
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Exploded View
INFOID:0000000007541407
NOTE:
The same procedure is also performed for front power window switch (passenger side) and rear power switch
(LH & RH).
Refer to removal and installation procedure. Refer to
PWC-92, "Removal and Installation"
.
Removal and Installation
INFOID:0000000007541408
REMOVAL
1.
Remove the power window main switch finisher (2).
Refer to
INT-12, "FRONT DOOR FINISHER : Exploded View"
and
INT-12, "FRONT DOOR FINISHER : Removal and Installa-
2.
Power window main switch (1) is removed from power window
main switch finisher (2) using remover tool (A).
CAUTION:
Do not fold the pawl of power window main switch finisher.
NOTE:
The same procedure is also performed for front power window
switch (passenger side) and rear power window switch (LH & RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
Power window main switch is exchanged or is detached it is necessary to do the initialization procedure.
Refer to
PWC-6, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
JMKIA1823ZZ
1.
Power window main switch
2.
Power window main switch finisher
JMKIA1822ZZ
Revision: 2013 February
2012 MURANO
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
DTC/CIRCUIT DIAGNOSIS . . . . . . ..
CIGARETTE LIGHTER . . . . . . . . . ...
Wiring Diagram - CIGARETTE LIGHTER - . . . ...
POWER SOCKET . . . . . . . . . . . ...
Wiring Diagram - POWER SOCKET - . . . . . ...
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
FOR USA AND CANADA . . . . . . . . . . ....
FOR MEXICO . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
CIGARETTE LIGHTER . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
POWER SOCKET . . . . . . . . . . . ..
FRONT POWER SOCKET . . . . . . . . . . ..
FRONT POWER SOCKET : Exploded View . . ....
FRONT POWER SOCKET : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . .
CONSOLE POWER SOCKET . . . . . . . . ....
CONSOLE POWER SOCKET : Exploded View . ...
CONSOLE POWER SOCKET : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
LUGGAGE ROOM POWER SOCKET . . . . . ....
LUGGAGE ROOM POWER SOCKET : Exploded
View . . . . . . . . . . . . . . . . . . ..
LUGGAGE ROOM POWER SOCKET : Removal
and Installation . . . . . . . . . . . . . . .
Revision: 2013 February
2012 MURANO
PWO-2
< DTC/CIRCUIT DIAGNOSIS >
CIGARETTE LIGHTER
DTC/CIRCUIT DIAGNOSIS
CIGARETTE LIGHTER
Wiring Diagram - CIGARETTE LIGHTER -
INFOID:0000000007544979
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCMWM3147GB
Revision: 2013 February
2012 MURANO
PWO
POWER SOCKET
PWO-3
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SOCKET
Wiring Diagram - POWER SOCKET -
INFOID:0000000007544980
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCMWN0010GB
Revision: 2013 February
2012 MURANO
PWO-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000007544981
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000007544982
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Revision: 2013 February
2012 MURANO
PWO
PRECAUTIONS
PWO-5
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2013 February
2012 MURANO
PWO-6
< REMOVAL AND INSTALLATION >
CIGARETTE LIGHTER
REMOVAL AND INSTALLATION
CIGARETTE LIGHTER
Exploded View
INFOID:0000000007544983
Removal and Installation
INFOID:0000000007544984
REMOVAL
1.
Remove console finisher assembly. Refer to
.
2.
Pull out cigarette lighter (1).
3.
Disconnect cigarette lighter connector (A).
4.
Pull out cigarette lighter socket (2) by pushing the cigarette
lighter ring pawl (B) from the cigarette lighter socket hole
(square) (C).
5.
Remove cigarette lighter ring (3) from console finisher assembly
while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of cigarette lighter socket, cigarette lighter ring, and console finisher assembly.
1
: Cigarette lighter
2
: Cigarette lighter socket
3
: Cigarette lighter ring
JPMIA0784ZZ
D
: Cut out
JPMIA0785ZZ
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст