Nissan Murano Z51 (2012 year). Manual — part 91
WT-16
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING BCM
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000007544937
When replacing BCM, tire pressure sensor ID registration is required.
Work Procedure
INFOID:0000000007544938
1.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration.
>> Refer to
Revision: 2013 February
2012 MURANO
TIRE PRESSURE SENSOR WAKE UP OPERATION
WT-17
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE SENSOR WAKE UP OPERATION
Description
INFOID:0000000007544939
This procedure must be done after replacement of a tire pressure sensor, BCM, or rotation of wheels.
Work Procedure
INFOID:0000000007544940
1.
TIRE PRESSURE SENSOR WAKE-UP PROCEDURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low
tire pressure warning lamp.
2.
Contact the tire pressure sensor activation tool (J-45295) (1) to
the side of the tire at the location to the tire pressure sensor.
3.
Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the wake-up procedure starting from the vehicle
front left wheel, then repeat the procedure in the order of
the front right wheel, rear right wheel, and rear left wheel.
4.
Check that the turn signal lamps blink twice when the tire pres-
sure sensor wake-up procedure for all wheels is completed.
5.
Check that the low tire pressure warning lamp turns OFF, after
the tire pressure sensor wake-up procedure is completed for all wheels and turns OFF.
Is the tire pressure sensor wake-up procedure completed?
YES
>> Perform the tire pressure sensor ID registration procedure. Refer to
NO
>> Perform trouble diagnosis for the tire pressure sensor. Refer to
.
JPEIC0089GB
NNEIC0020ZZ
Revision: 2013 February
2012 MURANO
WT-18
< BASIC INSPECTION >
TIRE PRESSURE SENSOR ID REGISTRATION
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000007544941
This procedure must be done after replacing or rotating wheels, replacing tire pressure sensor or BCM.
Work Procedure
INFOID:0000000007544942
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
With CONSULT.
1.
Display the “WORK SUPPORT” screen and select “ID REGIST”.
Is the tire pressure sensor activation tool (J-45295) used for the tire pressure sensor ID registration proce-
dure?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITH TIRE PRESSURE SENSOR ACTI-
VATION TOOL)
1.
Turn the ignition switch ON.
2.
Select the start button on the “ID REGIST” screen.
3.
Contact the tire pressure sensor activation tool (J-45295) (1) to
the side of the tire at the location to the tire pressure sensor.
4.
Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
5.
When ID registration is completed, check the following pattern at each wheel.
6.
After the ID registration procedure for all wheels is completed, press “END” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
3.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITHOUT TIRE PRESSURE SENSOR
ACTIVATION TOOL)
1.
Adjust the tire pressure for all wheels to match the list below.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Red”
↓
“Green”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
Revision: 2013 February
2012 MURANO
TIRE PRESSURE SENSOR ID REGISTRATION
WT-19
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2.
Drive the vehicle at a speed at more than 40 km/h (25 MPH) for 3 minutes or more, then perform the tire
pressure sensor ID registration procedure.
3.
After ID registration for all wheels is completed, press “END” to end ID registration.
4.
Adjust the tire pressures for all wheels to the specified value. Refer to
.
Is ID registrations for all wheels completed?
YES
>> ID registration END.
NO
>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS). Refer to
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 31)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
ID registration position
CONSULT
Front LH
“Red”
↓
“Green”
Front RH
Rear RH
Rear LH
Revision: 2013 February
2012 MURANO
WT-20
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
Description
INFOID:0000000007544943
When the tire pressure monitoring system detects low inflation pressure, the low tire pressure warning lamps
in the combination meter comes on.
DTC Logic
INFOID:0000000007544944
DTC DETECTION LOGIC
NOTE:
182.7 kPa (1.9 kg/cm
2
, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm
2
,33 psi) vehicles.
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007544945
1.
CHECK TIRE PRESSURE
Check the internal pressure of all wheels. Refer to
.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
.
NO
>> After adjusting the air pressure, GO TO 2.
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
DTC
Display item
Malfunction detected condition
Possible cause
C1704
LOW PRESSURE FL
Front LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
• Low tire pressure
• Tire pressure sen-
sor malfunction
C1705
LOW PRESSURE FR
Front RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2013 February
2012 MURANO
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-21
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CAUTION:
Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is the inspection result normal?
YES
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
NO
>> GO TO 1.
Revision: 2013 February
2012 MURANO
WT-22
< DTC/CIRCUIT DIAGNOSIS >
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000007544946
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007544947
1.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is a tire pressure of 0 kPa (0 Psi) displayed for all wheels?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector and tire pressure receiver harness connector.
3.
Check the continuity between BCM harness connector and tire pressure receiver harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
C1708
[NO DATA] FL
Tire pressure data signal from the front left wheel tire
pressure sensor cannot be detected.
• Harness or connector
(Tire pressure receiver, BCM)
• ID registration is not finished
• Tire pressure sensor malfunction
• BCM malfunction
C1709
[NO DATA] FR
Tire pressure data signal from the front right wheel tire
pressure sensor cannot be detected.
C1710
[NO DATA] RR
Tire pressure data signal from the rear right wheel tire
pressure sensor cannot be detected.
C1711
[NO DATA] RL
Tire pressure data signal from the rear left wheel tire
pressure sensor cannot be detected.
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2013 February
2012 MURANO
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
WT-23
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT
1.
Connect the BCM harness connector.
2.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
3.
Check the voltage between the BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace tire pressure receiver. Refer to
WT-47, "Removal and Installation"
.
5.
CHECK ID REGISTRATION
Perform ID registration of all tire pressure sensors. Refer to
Can ID registration of all tire pressure sensors be completed?
YES
>> GO TO 6.
NO
>> Replace tire pressure sensor. Refer to
6.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
BCM
—
Voltage
(Approx.)
Connector
Terminal
M123
138
Ground
5 V
Revision: 2013 February
2012 MURANO
WT-24
< DTC/CIRCUIT DIAGNOSIS >
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
CAUTION:
Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM” to read the tire pressure for all wheels.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
.
NO
>> Replace BCM. Refer to
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive at a speed of 40 km/h (25 MPH) or more, for several
minutes without stopping.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2013 February
2012 MURANO
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
WT-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000007544948
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007544949
1.
CHECK TIRE PRESSURE
Check the internal pressure of all wheels. Refer to
.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
.
NO
>> After adjusting the tire pressure, GO TO 2.
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Check and adjust the tire pressure for all wheels. Refer to
.
2.
Perform tire pressure sensor ID registration for all wheels. Refer to
.
3.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
4.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
5.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.
6.
Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi).
Is the inspection 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi)?
YES
>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm
2
, 63.60 Psi) dis-
.
NO
>> GO TO 1.
DTC
Display item
Malfunction detected condition
Possible case
C1716
[PRESSDATA ERR] FL
Malfunction in the tire pressure data from the front left
wheel tire pressure sensor.
• ID registration is not fin-
ished
• Tire pressure sensor mal-
function
C1717
[PRESSDATA ERR] FR
Malfunction in the tire pressure data from the front right
wheel tire pressure sensor.
C1718
[PRESSDATA ERR] RR
Malfunction in the tire pressure data from the rear right
wheel tire pressure sensor.
C1719
[PRESSDATA ERR] RL
Malfunction in the tire pressure data from the rear left wheel
tire pressure sensor.
Revision: 2013 February
2012 MURANO
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1729 VEHICLE SPEED SIGNAL
C1729 VEHICLE SPEED SIGNAL
Description
INFOID:0000000007544950
BCM detects no vehicle speed signal.
DTC Logic
INFOID:0000000007544951
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007544952
1.
PERFORM COMBINATION METER SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” of “METER/M&A”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Replace BCM. Refer to
WT-8, "COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)"
NO
>> GO TO 3.
3.
CHECK INFORMATION
With CONSULT
1.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2.
Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
>> Replace BCM. Refer to
DTC
Display item
Malfunction detected condition
Possible case
C1729
VHCL SPEED SIG ERR
Vehicle speed signal not detected.
• CAN communication error
• Combination meter malfunction
Revision: 2013 February
2012 MURANO
C1734 BCM
WT-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1734 BCM
DTC Logic
INFOID:0000000007544953
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
CAUTION:
Perform within 15 minutes after stop the vehicle.
Is DTC “C1734” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007544954
1.
CHECK BCM POWER SUPPLY
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check voltage between BCM harness connector terminals and ground.
Is the power supply normal?
YES
>> GO TO 2.
NO
>>
Check the following. If any items are damaged, repair or replace damage parts.
• 40A fusible link [No. L located in the fuse block]. Refer to
PG-108, "Fuse and Fusible Link
.
• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to
PG-107, "Fuse, Connector and Termi-
• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check the Battery voltage.
2.
CHECK BCM GROUND
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Disconnect tire pressure receiver harness connector.
2.
Check the continuity between BCM harness connector and tire pressure receiver harness connector.
DTC
Display item
Malfunction detected condition
Possible case
C1734
CONTROL UNIT
Tire pressure monitoring system malfunction in BCM
BCM malfunction
BCM
—
Voltage
(Approx.)
Connector
Terminal
M118
1
Ground
Battery voltage
M119
11
BCM
—
Continuity
Connector
Terminal
M119
13
Ground
Existed
Revision: 2013 February
2012 MURANO
WT-28
< DTC/CIRCUIT DIAGNOSIS >
C1734 BCM
3.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK BCM
Check the BCM input/output signal. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK BCM HARNESS CONNECTOR
Check the BCM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
NO
>> Check for looseness or damage at the harness connector pins of the low tire pressure warning
control unit. Repair or replace if necessary.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
Revision: 2013 February
2012 MURANO
TIRE PRESSURE RECEIVER
WT-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE RECEIVER
Component Function Check
INFOID:0000000007544955
1.
TIRE PRESSURE MONITORING SYSTEM OPERATION
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use CONSULT “DATA MONITOR” to display the tire pressure for
all wheels.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000007544956
1.
CHECK TIRE PRESSURE RECEIVER SIGNAL
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check tire pressure receiver connector and ground signal with oscilloscope.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect tire pressure receiver connector.
3.
Turn the ignition switch ON.
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Tire pressure receiver
—
Condition
Voltage
(Approx.)
Connector
Terminal
M21
2
Ground
Stand by state
When receiving the signal from the tire
pressure sensor
OCC3881D
OCC3880D
Revision: 2013 February
2012 MURANO
WT-30
< DTC/CIRCUIT DIAGNOSIS >
TIRE PRESSURE RECEIVER
CAUTION:
Never start the engine.
4.
Check voltage between tire pressure receiver connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector and tire pressure receiver connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK BCM CIRCUIT
Inspect the BCM circuit. Refer to
.
Is the BCM circuit normal?
YES
>> Replace tire pressure receiver. Refer to
WT-47, "Removal and Installation"
NO
>> Replace BCM. Refer to
Tire pressure receiver
—
Voltage
(Approx.)
Connector
Terminal
M21
4
Ground
5.0 V
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
Revision: 2013 February
2012 MURANO
LOW TIRE PRESSURE WARNING LAMP
WT-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP
Component Function Check
INFOID:0000000007544957
1.
CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP
Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000007544958
1.
POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
MWI-6, "METER SYSTEM : System Description"
NO
>> Replace the BCM. Refer to
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст