Nissan Teana J32. Manual — part 9
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ENTRY ASSIST FUNCTION : Component Parts Location
INFOID:0000000003859814
1.
BCM M118, M119, M122, M123
2.
Combination meter M34
3.
Key slot M99
4.
Seat memory switch D13
5.
Front door switch (driver side) B34
6.
Reclining motor (driver side) B454
7.
Lifting motor (front) (driver side)
B455
8.
Driver seat control unit B451,B452
9.
Sliding motor (driver side) B461
JMJIA1811ZZ
ADP-30
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Description
INFOID:0000000003759087
CONTROL UNITS
INPUT PARTS
Sensors
OUTPUT PARTS
INTELLIGENT KEY INTERLOCK FUNCTION
10. Lifting motor (rear) (driver side) B456 11.
Power seat switch (driver side) B459
(sliding, lifting switch)
12. Power seat switch (driver side) B459
(reclining switch)
13. TCM (transmission control module)
F23
14. Control device (detention switch)
M57
15. ABS actuator and electric unit (con-
trol unit) E36
A.
Behind the combination meter
B.
View with seat cushion and seatback
pad removed
C.
Back side of the seat cushion
D.
Engine room (LH)
E.
View with the center console assem-
bly removed
F.
Engine room (RH)
Item
Function
Driver seat control unit
Operates the seat sliding motor for a certain amount depending on the ignition sig-
nal and door switch signal (driver side) from BCM
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication
• Ignition switch position: ACC/ON
Item
Function
Sliding sensor
Detect the front/rear position of seat
Item
Function
Sliding motor
Slides the seat frontward/rearward
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-31
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION : System Diagram
INFOID:0000000003759088
INTELLIGENT KEY INTERLOCK FUNCTION : System Description
INFOID:0000000003759089
OUTLINE
When unlocking doors by Intelligent Key or door request switch (driver side), the memory function is per-
formed first, the exit assist function is performed next and the entry assist function is performed last.
OPERATION PROCEDURE
1.
Unlock doors by using Intelligent Key or door request switch (driver side).
2.
The system performs exit assist operation and memory operation.
NOTE:
Further information for Intelligent Key interlock function. Refer to
ADP-8, "MEMORY STORING : Description"
.
OPERATION CONDITION
Satisfy all of the following items. The Intelligent Key interlock function is not performed if any of these items
are not satisfied.
DETAIL FLOW
JMJIA1815GB
Item
Request status
Ignition position
OFF
Steering lock unit
LOCK
Switch inputs
• Power seat switch
• Set switch
• Memory switch
OFF
(Not operated)
Selector lever
P position
ADP-32
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
Order
Input
Output
Control unit condition
1
• Door unlock signal
(CAN)
• Key ID signal (CAN)
—
Driver seat control unit receives the door unlock signal and the key
ID signal from BCM when unlocking the door with Intelligent Key or
driver side door request switch
2
—
—
Driver seat control unit performs the memory function
3
—
—
Driver seat control unit performs the exit assist function
4
—
—
Driver seat control unit performs the entry assist function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст