Nissan Teana J32. Manual — part 655
HA-48
< ON-VEHICLE REPAIR >
CONDENSER PIPE ASSEMBLY
CONDENSER PIPE ASSEMBLY
Exploded View
INFOID:0000000003795844
Removal and Installation
INFOID:0000000003795845
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove mounting bolt (A), and then disconnect high-pressure
flexible hose (1) and high-pressure pipe (2) from condenser pipe
assembly.
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
3.
Remove mounting bolt (A), and then remove condenser pipe
assembly (1) from condenser.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
Refer to
for symbols in the figure.
JPIIA0978GB
JPIIA0979ZZ
JPIIA0980ZZ
CONDENSER PIPE ASSEMBLY
HA-49
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
HA-50
< ON-VEHICLE REPAIR >
LIQUID TANK
LIQUID TANK
Exploded View
INFOID:0000000003795848
Removal and Installation
INFOID:0000000003795849
REMOVAL
1.
Remove condenser. Refer to
.
2.
Clean liquid tank and its surrounding area. Then remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
3.
Remove mounting bolts (A), and then remove liquid tank (1).
CAUTION:
Cap or wrap the joint of the A/C piping and liquid tank with
suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
Refer to
for symbols in the figure.
JPIIA0978GB
JPIIA0984ZZ
REFRIGERANT PRESSURE SENSOR
HA-51
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000003795850
Removal and Installation
INFOID:0000000003795851
REMOVAL
1.
Remove liquid tank. Refer to
.
2.
Fix the liquid tank (1) with a vise (A). Remove the refrigerant
pressure sensor (2) with a wrench (B).
CAUTION:
Be careful not to damage liquid tank.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
Refer to
JPIIA0978GB
JSIIA0075ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст