Nissan Teana J32. Manual — part 1082
SRC-82
< COMPONENT DIAGNOSIS >
B1129 SIDE MODULE RH
B1129 SIDE MODULE RH
Description
INFOID:0000000003814029
For front RH side air bag module, crash is judged by main “G” sensor output signal (left side: LH satellite sen-
sor, right side: RH satellite sensor) and safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Front RH side air bag module is installed on the side of front seat back with fixed nuts.
DTC Logic
INFOID:0000000003814030
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status.
SRC-10, "Air Bag Warning Lamp Diagnosis"
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003814031
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1129
SIDE MODULE RH
[OPEN]
Front RH side air bag module circuit is
open
• Disconnection of wiring harness and
open
• Malfunction in front RH side air bag
module
• Malfunction in air bag diagnosis sen-
sor unit
B1129 SIDE MODULE RH
SRC-83
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> Replace wiring harness.
3.
REPLACE FRONT SIDE AIR BAG MODULE
1.
Replace front RH side air bag module. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-84
< COMPONENT DIAGNOSIS >
B1130 SIDE MODULE RH
B1130 SIDE MODULE RH
Description
INFOID:0000000003814032
For front RH side air bag module, crash is judged by main “G” sensor output signal (left side: LH satellite sen-
sor, right side: RH satellite sensor) and safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic
INFOID:0000000003814033
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-10, "Air Bag Warning Lamp Diagnosis"
.
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003814034
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1130
SIDE MODULE RH
[VB-SHORT]
Front RH side air bag module circuit is
shorted to some power supply circuit
• Disconnection of wiring harness and
short
• Malfunction in front RH side air bag
module
• Malfunction in air bag diagnosis sen-
sor unit
B1130 SIDE MODULE RH
SRC-85
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> Replace wiring harness.
3.
REPLACE FRONT SIDE AIR BAG MODULE
1.
Replace front RH side air bag module. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст