Nissan Teana J32. Manual — part 509
EXL-6
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
ON-VEHICLE MAINTENANCE . . . . ..
HEADLAMP AIMING ADJUSTMENT . . . .
Description . . . . . . . . . . . . . . . .
Aiming Adjustment Procedure (Low Beam) . . ...
Aiming Adjustment Procedure (High Beam) . . ..
FRONT FOG LAMP AIMING ADJUSTMENT .
Description . . . . . . . . . . . . . . . .
Aiming Adjustment Procedure . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . ...
FRONT COMBINATION LAMP . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . ...
FRONT FOG LAMP . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
OPTICAL SENSOR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
LIGHTING & TURN SIGNAL SWITCH . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
HEADLAMP AIMING SWITCH . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
SIDE TURN SIGNAL LAMP . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR COMBINATION LAMP . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
HIGH-MOUNTED STOP LAMP . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR FOG LAMP . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
LICENSE PLATE LAMP . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW
EXL-7
< BASIC INSPECTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000003773518
OVERALL SEQUENCE
DETAILED FLOW
1.
INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
JPLIA0313GB
EXL-8
< BASIC INSPECTION >
[XENON TYPE]
DIAGNOSIS AND REPAIR WORKFLOW
>> GO TO 2.
2.
SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.
BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.
SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.
FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES
>> GO TO 7.
NO
>> GO TO 8.
7.
SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.
SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.
MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.
REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 11.
11.
REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 3.
INSPECTION AND ADJUSTMENT
EXL-9
< BASIC INSPECTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003894984
CAUTION:
• When replacing the auto levelizer control unit, you must perform “WRITE CONFIGURATION” with
CONSULT-III.
- Complete the procedure of “WRITE CONFIGURATION” in order.
• When replacing the auto levelizer control unit, perform “SENSOR INITIALIZE” with CONSULT-III.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003894985
1.
WRITING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform “WRITE CONFIGURATION” to write vehicle specification. Refer to
(HEADLAMP LEVELIZER) : Special Repair Requirement"
.
>> GO TO 2.
2.
SENSOR INITIALIZE
CONSULT-III Work support
Perform “SENSOR INITIALIZE”. Refer to
EXL-10, "SENSOR INITIALIZE : Special Repair Requirement
(HEADLAMP AIMING CONTROL SYSTEM)"
>> WORK END
CONFIGURATION (HEADLAMP LEVELIZER)
CONFIGURATION (HEADLAMP LEVELIZER) : Description
INFOID:0000000003894986
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing the auto
levelizer control unit.
CAUTION:
• When replacing the auto levelizer control unit, you must perform “WRITE CONFIGURATION” with
CONSULT-III.
• Complete the procedure of “WRITE CONFIGURATION” in order.
CONFIGURATION (HEADLAMP LEVELIZER) : Special Repair Requirement
INFOID:0000000003894987
1.
WRITE CONFIGURATION
CONSULT-III Configuration
1.
Select “WRITE CONFIGURATION”.
2.
Select “Setting change”.
3.
When “COMMAND FINISHED”, select “END”.
>> WORK END
SENSOR INITIALIZE
Function
Description
WRITE CONFIGURATION
Writes the vehicle configuration automatically.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст