Nissan Teana J32. Manual — part 1000
FRONT SEAT
SE-133
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER'S POWER SEAT
19. Seatback duct B
20. Seatback duct C
21. Clip
22. Seat slide and lifter switch knob
23. Reclining switch knob
24. Seat cushion outer finisher
25. Seat control switch
26. Seat cushion outer finisher inside
27. Seat harness clamp
28. Seat harness
29. Side air bag module
30. Seatback finisher
31. Side air bag module bracket
32. Seat cushion rear finisher
33. Seatback board
34. Seatback silencer
35. Seatback heater unit
36. Seat cushion heater unit
37. Seat slide inner cover
38. Lumbar support unit
39. Seat cushion inner finisher
40. Seat cushion inner finisher inside
41. TORX bolt
42. Seat frame assembly
43. TORX bolt
44. Seat slide outer cover
45. Rear slide cover
46. End cap
47. Reclining device outer cover
48. Reclining device inner cover
49. Headrest holder (locked)
50. Headrest holder (free)
Refer to
SE-134
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
FRONT SEAT
1.
Seatback board
2.
Seat cushion rear finisher
3.
Side air bag module bracket
4.
Seatback finisher
5.
Side air bag module
6.
Seat harness
7.
Seat harness clamp
8.
Reclining switch knob
9.
Seat slide and lifter switch knob
10. Seat cushion outer finisher
11.
Seatback duct B
12. Seatback duct A
13. Ventilation motor
14. Blower filter
15. Seat cushion duct A
16. Seat cushion duct B
17. Clip
18. Ventilation seat control unit
JMJIA1715GB
FRONT SEAT
SE-135
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000003840024
REMOVAL
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Before removal, turn ignition switch OFF, disconnect battery negative terminal, and then wait for at
least 3 minutes.
NOTE:
Confirming a position of connector before work.
1.
Remove the headrest.
2.
Slide the seat to the frontmost position.
3.
Remove the rear outer mounting TORX bolt.
4.
Remove the rear inner mounting TORX bolt.
5.
Slide the seat to the rearmost position.
6.
Remove the front slide cover.
• Open the front end of the front slide cover to release the
pawls.
• Slide the front slide cover forward to release the pawls.
7.
Remove the front outer mounting TORX bolt.
8.
Remove the front inner mounting TORX bolt.
9.
Set seatback in a standing position.
10. Lift the seat to the uppermost position.
11. Disconnect harness connector under the seat and remove harness clamps.
12. Remove seat from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation, turn ignition switch OFF, disconnect battery negative terminal, and then wait for
at least 3 minutes.
• Clamp the harness in position.
Disassembly and Assembly
INFOID:0000000003840025
SEATBACK
19. Clip
20. Seatback duct C
21. Front slide cover
22. Ottoman trim and pad
23. Front outer link cover
24. Rear outer link cover
25. Ottoman unit assembly
26. Front inner link cover
27. Rear inner link cover
28. Ottoman protector
29. Seat cushion inner finisher inside
30. Seat cushion inner finisher
31. Seat belt buckle
32. Seat cushion heater unit
33. Seat cushion pad
34. Seat cushion trim
35. Seatback pad
36. Seatback trim
37. Headrest
38. Seatback heater unit
39. Seatback silencer
40. Reclining device inner cover
41. Reclining device outer cover
42. Rear slide cover
43. End cap
44. Seat cushion outer finisher inside
45. Seat control switch
46. TORX bolt
47. TORX bolt
48. Seat frame assembly
49. Seat slide inner cover
50. Headrest holder (locked)
51. Headrest holder (free)
Refer to
: Pawl
JMJIA1863ZZ
SE-136
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
FRONT SEAT
Disassembly
1.
Remove the seatback board.
• Remove the hook, and then remove screws (A).
• Remove the pawls, and then pull out seatback board.
• Pull down the seatback board to release the upper pawls.
2.
Remove the lumbar support lever knob. (With lumbar support model)
Pull snap pin (1) upward, and remove lumbar support lever knob
(2) from seatback using hook and pick tool.
3.
Remove the seatback pad and seatback trim.
• Remove the seatback retainer on the back side of the seat-
back.
• Remove the screws, and then remove seatback finisher.
• Remove the side air bag module. Refer to
JMJIA1864ZZ
: Pawl
JMJIA1865ZZ
JMJIA0252ZZ
JMJIA1867ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст