Nissan Teana J32. Manual — part 801
ENGINE MAINTENANCE
MA-13
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
ENGINE MAINTENANCE
DRIVE BELT
DRIVE BELT : Exploded View
INFOID:0000000003862446
DRIVE BELT : Checking
INFOID:0000000003862447
WARNING:
Be sure to perform the this step when engine is stopped.
• Check that the indicator (A) of drive belt auto-tensioner is within the possible use range (C).
NOTE:
• Check the drive belt auto-tensioner indication when the engine is cold.
• When new drive belt is installed, the indicator should be within the range (B) in the figure.
• Visually check entire drive belt for wear, damage or cracks.
• If the indicator is out of the possible use range or belt is damaged, replace drive belt.
DRIVE BELT : Tension Adjustment
INFOID:0000000003862448
.
ENGINE COOLANT
ENGINE COOLANT : Inspection
INFOID:0000000003862449
LEVEL
JPBIA1625ZZ
1.
Idler pulley
2.
Drive belt
3.
Power steering oil pump
4.
Drive belt auto-tensioner
5.
Crankshaft pulley
6.
Idler pulley
7.
A/C compressor
8.
Alternator
A.
Indicator
B.
Range when new drive belt is installed
C.
Possible use range
D.
View D
: Engine front
MA-14
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE
• Check if the reservoir tank engine coolant level is within the “MIN”
to “MAX” when the engine is cool.
• Adjust the engine coolant level as necessary.
LEAKAGE
• To check for leakage, apply pressure to the cooling system with the
radiator cap tester (commercial service tool) (A) and radiator cap
tester adapter (commercial service tool) (B).
WARNING:
Never remove radiator cap when engine is hot. Serious burns
could occur from high-pressure engine coolant escaping from
radiator.
CAUTION:
Higher test pressure than specified may cause radiator dam-
age.
NOTE:
In a case that engine coolant decreases, replenish radiator with engine coolant.
• If anything is found, repair or replace damaged parts.
ENGINE COOLANT : Draining
INFOID:0000000003862450
WARNING:
• To avoid being scalded, never change engine coolant when the engine is hot.
• Wrap a thick cloth around radiator cap and carefully remove radiator cap. First, turn radiator cap a
quarter of a turn to release built-up pressure. Then turn radiator cap all the way.
1.
Remove engine under cover.
2.
Open radiator drain plug (1) at the bottom of radiator, and then
remove radiator cap.
When draining all of engine coolant in the system, open water drain plugs on cylinder block. Refer
to
EM-110, "Disassembly and Assembly"
3.
Remove reservoir tank as necessary, and drain engine coolant and clean reservoir tank before installing.
4.
Check drained engine coolant for contaminants such as rust, corrosion or discoloration.
If contaminated, flush the engine cooling system. Refer to
MA-16, "ENGINE COOLANT : Flushing"
ENGINE COOLANT : Refilling
INFOID:0000000003862451
1.
Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
A
: MAX
B
: MIN
JPBIA0102ZZ
Testing pressure
: Refer to
.
PBIC5121J
: Vehicle front
JPBIA2225ZZ
ENGINE MAINTENANCE
MA-15
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
If water drain plugs on cylinder block are removed, close and tighten them. Refer to
2.
Check that each hose clamp has been firmly tightened.
3.
Remove air duct assembly and air cleaner cases (upper and lower) assembly. Refer to
.
4.
Disconnect heater hose (1) at the position (
) in the figure.
5.
Fill radiator, and reservoir tank if removed, to specified level.
CAUTION:
Never adhere the engine coolant to electronic equipments.
(alternator etc.)
• Pour engine coolant through engine coolant filler neck
slowly of less than 2 (1-3/4 lmp qt) a minute to allow air
in system to escape.
• When engine coolant overflows disconnected heater
hose, connect heater hose, and continue filling the engine
coolant.
• Use Genuine NISSAN Engine Coolant or equivalent in its
quality mixed with water (distilled or demineralized). Refer
to
MA-11, "Fluids and Lubricants"
6.
Install air duct assembly and air cleaner cases (upper and lower) assembly. Refer to
.
7.
Install radiator cap.
8.
Warm up engine until opening thermostat. Standard for warming-up time is approximately 10 minutes at
3,000 rpm.
• Check thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.
CAUTION:
Tightening torque
: Refer to
: Vehicle front
JPBIA2226ZZ
Engine coolant capacity
: Refer to
CO-27, "Periodical Maintenance Spec-
(With reservoir tank at “MAX” level)
Reservoir tank engine coolant capacity
:Refer to
CO-27, "Periodical Maintenance Spec-
(At “MAX” level)
A
: MAX
B
: MIN
JPBIA0412ZZ
JPBIA0102ZZ
MA-16
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE
Watch water temperature gauge so as not to overheat engine.
9.
Stop the engine and cool down to less than approximately 50
°
C (122
°
F).
• Cool down using fan to reduce the time.
• If necessary, refill radiator up to filler neck with engine coolant.
CAUTION:
Never adhere the engine coolant to electronic equipments. (alternator etc.)
10. Refill reservoir tank to “MAX” level line with engine coolant.
11. Repeat steps 7 through 10 two or more times with radiator cap installed until engine coolant level no
longer drops.
12. Check cooling system for leakage with engine running.
13. Warm up the engine, and check for sound of engine coolant flow while running engine from idle up to
3,000 rpm with heater temperature controller set at several position between “COOL” and “WARM”.
• Sound may be noticeable at heater unit.
14. Repeat step 13 three times.
15. If sound is heard, bleed air from cooling system by repeating step 5, and steps from 7 to 14 until engine
coolant level no longer drops.
ENGINE COOLANT : Flushing
INFOID:0000000003862452
1.
Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to
2.
Remove air duct assembly and air cleaner cases (upper and lower) assembly. Refer to
.
3.
Disconnect heater hose (1) at the position (
) in the figure.
4.
Fill radiator and reservoir tank with water and reinstall radiator cap.
CAUTION:
Never adhere the water to electronic equipments. (alternator etc.)
• When water overflows disconnected heater hose, connect heater hose, and continue filling the
water.
5.
Run the engine and warm it up to normal operating temperature.
6.
Rev the engine two or three times under no-load.
7.
Stop the engine and wait until it cools down.
8.
Drain water from the system. Refer to
MA-14, "ENGINE COOLANT : Draining"
.
9.
Repeat steps 1 through 8 until clear water begins to drain from radiator.
RADIATOR CAP
Tightening torque
: Refer to
: Vehicle front
JPBIA2226ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст