Nissan Teana J32. Manual — part 475
EM-24
< ON-VEHICLE REPAIR >
ENGINE COVER
ON-VEHICLE REPAIR
ENGINE COVER
Exploded View
INFOID:0000000003802246
Removal and Installation
INFOID:0000000003802247
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Remove engine cover mounting bolts (A), (B).
3.
Draw and pull out engine cover from engine cover mounting bolts (C), (D).
CAUTION:
• Pull engine cover from mounting bolt (D) holding with hand the position (E) as shown in the fig-
ure.
• Never damage or scratch engine cover when installing or removing.
4.
Remove engine mounting bolts (C), (D), if necessary.
INSTALLATION
Install in the reverse order of removal.
1.
Engine cover
Refer to
for symbols in the figure.
JPBIA1712GB
JPBIA1718ZZ
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
EM-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
Exploded View
INFOID:0000000003802248
Removal and Installation
INFOID:0000000003802249
Removal
1.
Remove drive belt. Refer to
EM-12, "Removal and Installation"
.
• Keep auto-tensioner pulley arm locked after drive belt is removed.
2.
Remove auto-tensioner and idler pulley.
• Keep auto-tensioner pulley arm locked to install or remove auto-tensioner.
Installation
Installation is the reverse order of removal.
CAUTION:
If there is damage greater than peeled paint, replace drive belt auto-tensioner.
1.
Drive belt auto-tensioner
2.
Idler pulley
3.
Idler pulley
4.
Bracket
Refer to
JPBIA1626GB
EM-26
< ON-VEHICLE REPAIR >
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000003802250
Removal and Installation
INFOID:0000000003802251
REMOVAL
1.
Remove air duct (inlet).
2.
Disconnect harness connector from mass air flow sensor.
3.
Disconnect PCV hose.
4.
Remove air cleaner cases (upper and lower) with mass air flow sensor and air duct assembly disconnect-
ing their joints.
• Add mating marks as necessary for easier installation.
5.
Remove mass air flow sensor from air cleaner case (upper), as necessary.
CAUTION:
Handle mass air flow sensor with following cares.
• Never shock mass air flow sensor.
• Never disassemble mass air flow sensor.
1.
Mass air flow sensor
2.
Air cleaner case (upper)
3.
Air cleaner filter
4.
Clamp
5.
Air duct assembly
6.
Clamp
7.
PCV hose
8.
Air duct (inlet)
9.
Grommet
10. Collar
11.
Grommet
12. Grommet
13. Bracket
14. Bracket
15. Collar
16. Grommet
17. Air cleaner case (lower)
A.
To electric throttle control actuator
B.
To rocker cover (bank 2)
C.
VQ25DE
for symbols in the figure.
JPBIA2193GB
AIR CLEANER AND AIR DUCT
EM-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Never touch mass air flow sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align marks. Attach each joint. Screw clamps firmly.
Inspection
INFOID:0000000003802252
INSPECTION AFTER REMOVAL
Inspect air duct assembly for crack or tear.
• If anything found, replace air duct assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст