Nissan Teana J32. Manual — part 759
INT-56
< ON-VEHICLE REPAIR >
HEADLINING
CAUTION:
• When removing, 2 workers are required. (1 for the front and rear of headlining)
• Cover center console finisher upper surface with a shop cloth to prevent it from being damaged.
• Never bend headlining when removing.
13. Remove the following parts after removing headlining.
• Map lamp assembly. Refer to
INL-89, "Removal and Installation"
• Personal lamp assembly. Refer to
INL-96, "Removal and Installation"
.
• Roof harness assembly.
• Antenna feeder assembly. Refer to
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install headlining assembly after inserting clips to clip holder of headlining rear end.
• Never bend headlining when installing.
TRUNK ROOM TRIM
INT-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
TRUNK ROOM TRIM
Exploded View
INFOID:0000000003819232
Removal and Installation
INFOID:0000000003819233
REMOVAL
1.
Fully open trunk lid assembly.
1.
Trunk front finisher upper
2.
Rear seatback center finisher (Nor-
mal roof models)
3.
Rear seatback center finisher lid
4.
Rear wheel house finisher (LH)
5.
Trunk floor spacer (LH)
6.
Trunk center box assembly
7.
Trunk rear finisher
8.
Rear wheel house finisher (RH)
9.
Trunk front finisher center
10. Trunk floor carpet
11. Trunk floor spacer (RH)
12. Rear seatback center finisher (Sun-
roof models)
: Clip
: Metal clip
JMJIA1806ZZ
INT-58
< ON-VEHICLE REPAIR >
TRUNK ROOM TRIM
2.
Remove trunk floor carpet.
3.
Remove trunk center box.
4.
Remove trunk floor spacer (LH/RH).
5.
Remove trunk rear finisher mounting clips and metal clips, and then remove trunk rear finisher.
6.
Remove trunk weather-strip.
7.
Remove trunk front finisher center fixing clips, and then remove trunk front finisher center.
8.
Remove trunk front finisher upper fixing clips, and then remove the trunk front finisher upper.
9.
Remove rear wheel house finisher (LH/RH).
• Remove rear wheel fixing clips
• Remove rear seat assembly. Refer to
SE-99, "Removal and Installation"
.
• Remove rear seat support (1) fixing bolts, shown by the arrows in the figure below and then remove rear
wheel house finisher (2)
10. Disengage rear seatback center finisher assembly fixing clips with a remover tool (A), and then remove
rear seatback center finisher assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check that clips, pawls, metal clips are securely fitted in panel holes on body when installing, and then
press them in.
: Bolt
JMJIA1791ZZ
TRUNK LID TRIM
INT-59
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
TRUNK LID TRIM
Exploded View
INFOID:0000000003819234
Removal and Installation
INFOID:0000000003819235
REMOVAL
1.
Fully open trunk lid assembly.
2.
Disengage the trunk lid pull handle (1) fixing pawls with a remover tool (A), and then remove the trunk lid
pull handle.
1.
Trunk lid finisher inner
2.
Trunk lid assembly
3.
Emergency handle
4.
Trunk lid pull handle
: Pawl
JMJIA1807ZZ
: Pawl
JMJIA1792ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст