Nissan Teana J32. Manual — part 1210
VTL-26
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
SUNLOAD SENSOR
SUNLOAD SENSOR
Exploded View
INFOID:0000000003774667
Removal and Installation
INFOID:0000000003774668
REMOVAL
1.
Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
1.
Sunload sensor
JPIIA0904ZZ
JPIIA0905ZZ
INTAKE SENSOR
VTL-27
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
INTAKE SENSOR
Exploded View
INFOID:0000000003821339
1.
Ventilator seal
2.
Defroster seal
3.
Distributor upper case
4.
Center case
5.
Heater & cooling unit case cover
6.
Foot duct 1 (right)
7.
Foot duct 2 (right)
8.
Air mix door motor (passenger side)
9.
Evaporator pipe assembly
10.
Expansion valve
11.
O-ring
12. Evaporator
13.
Filter cover
14.
Air conditioner filter
15. Case packing
16.
Heater & cooling unit case (right)
17.
Cooler pipe grommet
18. Grommet
19.
Heater pipe grommet
20.
Heater pipe support
21. Drain hose
22.
Heater & cooling unit case (left)
23.
Air mix door motor (driver side)
24. Heater core
25.
Heater pipe cover
26.
Foot duct 2 (left)
27. Foot duct 1 (left)
28.
Aspirator hose
29.
Aspirator
30. Mode door motor
31.
Main link
32.
Rod link
33. Ventilator door link
34.
Mode door lever
35.
Ventilator door lever
36. Max. cool door link
JPIIA0906GB
VTL-28
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
INTAKE SENSOR
Removal and Installation
INFOID:0000000003774670
REMOVAL
1.
Remove evaporator pipe assembly. Refer to
.
2.
Disconnect intake sensor connector.
3.
Slide evaporator (1) toward the right side of the vehicle (as
shown in the figure), and then remove intake sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Do not rotate the bracket insertion part when removing and installing the intake sensor.
• Check for refrigerant leakage when charging refrigerant.
37. Defroster door link
38.
Foot door link
39.
Max. cool door lever
40. Foot door lever
41.
Defroster door lever
42.
Adapter case
43. Distributor lower case
44.
Ventilator door
45.
Intake sensor
46. Intake sensor bracket
47.
Foot door
48.
Max. cool door
49. Defroster door
50.
Air mix door (Slide door)
for symbols in the figure.
JPIIA0907ZZ
BLOWER UNIT
VTL-29
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER UNIT
Exploded View
INFOID:0000000003774671
DISASSEMBLY
1.
Blower unit
2.
Heater & cooling unit assembly
3.
Steering member
4.
Instrument stay
5.
Instrument panel assembly
Refer to
for symbols in the figure.
JPIIA0914GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст