Nissan Teana J32. Manual — part 436
EC-282
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
P1715 INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)
>> INSPECTION END
P1720 VSS
EC-283
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1720 VSS
Description
INFOID:0000000003856765
ECM receives two vehicle speed signals via the CAN communication line. One is sent from “ABS actuator and
electric unit (control unit)” via combination meter, and the other is from TCM (Transmission control module).
ECM uses these signals for engine control.
DTC Logic
INFOID:0000000003856766
DTC DETECTION LOGIC
NOTE:
• If DTC P1720 is displayed with DTC U1000, U1001 first perform the trouble diagnosis for DTC U1000,
U1001. Refer to
• If DTC P1720 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine.
2.
Drive vehicle at a speed of 20 km/h (12 MPH) or more for at least 5 seconds without depressing the brake
pedal.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003856767
1.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Perform trouble shooting relevant to DTC indicated.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1720
Vehicle speed sensor
(TCM output)
The difference between two vehicle speed
signals is out of the specified range.
• Harness or connectors
(Secondary speed sensor circuit is open or
shorted.)
• Harness or connectors
(Wheel sensor circuit is open or shorted.)
• TCM
• Secondary speed sensor
• ABS actuator and electric unit (control unit)
• Wheel sensor
• Combination meter
EC-284
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
P1720 VSS
3.
CHECK COMBINATION METER FUNCTION
.
>> INSPECTION END
P1800 VIAS CONTROL SOLENOID VALVE 1
EC-285
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1800 VIAS CONTROL SOLENOID VALVE 1
Description
INFOID:0000000003856768
The VIAS control solenoid valve 1 cuts the intake manifold vacuum signal for power valve 1 control. It
responds to ON/OFF signals from the ECM. When the solenoid is OFF, the vacuum signal from the intake
manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and sends the vac-
uum signal to the power valve actuator 1.
DTC Logic
INFOID:0000000003856769
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for at least 5 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003856770
1.
CHECK VIAS CONTROL SOLENOID VALVE 1 POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect VIAS control solenoid valve 1 harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between VIAS control solenoid valve 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
2.
CHECK VIAS CONTROL SOLENOID VALVE 1 OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between VIAS control solenoid valve 1 harness connector and ECM harness con-
nector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1800
VIAS control solenoid valve 1
circuit
An excessively low or high voltage signal
is sent to ECM through the VIAS control
solenoid valve 1.
• Harness or connectors
(The solenoid valve 1 circuit is open or
shorted.)
• VIAS control solenoid valve 1
VIAS control solenoid valve 1
Ground
Voltage
Connector
Terminal
F74
1
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст