Nissan Teana J32. Manual — part 1157
TM-152
< ON-VEHICLE MAINTENANCE >
[CVT: RE0F09B]
CVT POSITION
CVT POSITION
Inspection and Adjustment
INFOID:0000000003849084
INSPECTION
1.
Move selector lever to “P” position, and turn ignition switch ON (engine stop).
2.
Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.
3.
Move selector lever and check for excessive effort, sticking, noise or rattle.
4.
Check that selector lever stops at each position with the feel of engagement when it is moved through all
the positions. Check that the actual position of selector lever matches the position shown by shift position
indicator and manual lever on the transaxle.
5.
The method of operating selector lever to individual positions
correctly should be as shown.
6.
When selector button is pressed in “P”, “R”, “N”, “D” or “L” posi-
tion without applying forward/backward force to selector lever,
check button operation for sticking.
7.
Check that back-up lamps illuminate only when selector lever is
placed in the “R” position.
8.
When in “R” position, check that back-up lamps illuminate even
when the selector lever is pushed toward the “P” position.
CAUTION:
Check the lighting without pressing shift button.
9.
Check that back-up lamps do not illuminate when selector lever is pushed toward the “R” position when in
the “P” or “N” position.
CAUTION:
Check the lighting without pressing shift button.
10. Check that the engine can only be started with selector lever in the “P” and “N” positions.
11. Check that transaxle is locked completely in “P” position.
ADJUSTMENT
1.
Move selector lever to “ P” position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park
lock.
2.
Loosen the control cable nut (A).
3.
Place manual lever (B) to “P” position.
CAUTION:
Never apply any force to manual lever.
4.
Tighten the control cable nut. Refer to
.
CAUTION:
Fix manual lever when tightening.
JPDIA0343GB
JPDIA0794ZZ
TRANSMISSION CONTROL MODULE
TM-153
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
TRANSMISSION CONTROL MODULE
Exploded View
INFOID:0000000003849085
Removal and Installation
INFOID:0000000003849086
REMOVAL
CAUTION:
Never impact on TCM when removing or installing TCM.
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air duct (inlet). Refer to
3.
Disconnect TCM connector (A).
4.
Remove TCM (1) from bracket.
INSTALLATION
1.
Bracket
2.
TCM
: Vehicle front
Refer to
JPDIA0591GB
: Vehicle front
JPDIA0596ZZ
TM-154
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
TRANSMISSION CONTROL MODULE
Install in the reverse order of removal.
Adjustment
INFOID:0000000003849087
ADJUSTMENT AFTER INSTALLATION
After TCM is replaced. Refer to
TM-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Pre-
caution for TCM and CVT Assembly Replacement"
.
CONTROL DEVICE
TM-155
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL DEVICE
Exploded View
INFOID:0000000003849088
Removal and Installation
INFOID:0000000003849089
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
1.
Selector lever knob
2.
Lock pin
3.
Knob cover
4.
Control device assembly
5.
Shift lock unit
6.
Dust cover
Refer to
JPDIA0741GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст