Nissan Teana J32. Manual — part 360
FRONT DOOR LOCK
DLK-223
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• When installing each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000003817716
INSIDE HANDLE : Removal and Installation
INFOID:0000000003813429
REMOVAL
1.
Remove front door finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-33, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Disconnect inside handle cable.
3.
Remove inside handle mounting screws, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
Outside handle
2.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
3.
Rear gasket
4.
TORX bolt
5.
Key rod (driver side)
6.
Door lock assembly
7.
Inside handle escutcheon
8.
Inside handle
9.
Seal
10. Outside handle bracket
11.
Front gasket
: Vehicle front
Refer to
JMKIA2386GB
DLK-224
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000003817718
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000003813431
REMOVAL
1.
Remove front door finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-33, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Remove front door glass. Refer to
GW-17, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-20, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
1.
Outside handle
2.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
3.
Rear gasket
4.
TORX bolt
5.
Key rod (driver side)
6.
Door lock assembly
7.
Inside handle escutcheon
8.
Inside handle
9.
Seal
10. Outside handle bracket
11.
Front gasket
: Vehicle front
Refer to
for symbols in the figure.
JMKIA2386GB
FRONT DOOR LOCK
DLK-225
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never remove TORX bolt forcibly.
6.
Reach in to separate key rod (2) connection [on the door key
cylinder assembly (1)] (driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
: TORX bolt
JMKIA2094ZZ
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
DLK-226
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When installing each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
JMKIA2303ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст