Nissan Teana J32. Manual — part 611
FRONT DRIVE SHAFT BOOT
FAX-15
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
20. Install wheel sensor and sensor harness to steering knuckle. Refer to
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
(with
VDC).
TRANSAXLE SIDE
TRANSAXLE SIDE : Removal and Installation
INFOID:0000000003811081
Remove boot after removing drive shaft.
• Remove: refer to
FAX-18, "LEFT SIDE : Removal and Installation"
(right side).
• Disassembly: refer to
FAX-22, "TRANSAXLE SIDE : Disassembly and Assembly"
.
Inspection
INFOID:0000000003811082
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
SDIA1190J
FAX-16
< ON-VEHICLE REPAIR >
FRONT DRIVE SHAFT
FRONT DRIVE SHAFT
Exploded View
INFOID:0000000003812421
LEFT SIDE
VQ25DE
VQ35DE
JPDIF0193ZZ
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Boot band
7.
Boot
8.
Shaft
9.
Damper band
10. Dynamic damper
11.
Circular clip
12. Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0141ZZ
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Circular clip
7.
Joint sub-assembly
: Wheel side
FRONT DRIVE SHAFT
FAX-17
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE
VQ25DE
VQ35DE
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0184GB
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Spider assembly
9.
Snap ring
10. Housing
11.
Dust shield
12. Support bearing
13. Snap ring
14. Dust shield
15. Plate
16. Support bearing bracket
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0182GB
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band
6.
Dynamic damper
7.
Housing assembly
8.
Dust shield
9.
Snap ring
10. Support bearing
11.
Baring housing
12. Support bearing bracket
FAX-18
< ON-VEHICLE REPAIR >
FRONT DRIVE SHAFT
LEFT SIDE
LEFT SIDE : Removal and Installation
INFOID:0000000003811084
REMOVAL
1.
Remove tires.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-57, "FRONT WHEEL SENSOR : Exploded
(without VDC),
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
(with VDC).
3.
Remove lock plate of brake hose from strut assembly. Refer to
BR-19, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Exploded View"
.
5.
Remove disc rotor. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
6.
Remove cotter pin, and then loosen wheel hub lock nut. Refer to
.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage drive shaft from wheel hub and bearing
assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
joint sub-assembly and the other parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
8.
Remove wheel hub lock nut.
9.
Remove steering knuckle from strut assembly. Refer to
.
10. Remove drive shaft from wheel hub and bearing assembly.
11. Remove drive shaft from transaxle assembly.
• Use the drive shaft attachment (A) (SST: KV40107500) and a
sliding hammer (B) while inserting tip of the drive shaft attach-
ment between housing assembly and transaxle assembly.
CAUTION:
Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
(CVT: RE0F09B),
(CVT: RE0F10A).
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIG0070ZZ
JPDIF0004ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст