Nissan Teana J32. Manual — part 448
EC-330
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
ELECTRICAL LOAD SIGNAL
>> INSPECTION END
3.
CHECK HEADLAMP SYSTEM
(XENON TYPE) or
(HALOGEN TYPE).
>> INSPECTION END
4.
CHECK HEATER FAN CONTROL SYSTEM
.
>> INSPECTION END
ELECTRONIC CONTROLLED ENGINE MOUNT
EC-331
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ELECTRONIC CONTROLLED ENGINE MOUNT
Description
INFOID:0000000003856835
The electronic controlled engine mount control solenoid valve controls the intake manifold vacuum signal for
electronic controlled engine mount. The electronic controlled engine mount control solenoid valve is moved by
ON/OFF signal from the ECM. When the solenoid is OFF, the vacuum signal from the intake manifold is cut.
When the solenoid is ON, the intake manifold vacuum signal is sent to the electronic controlled engine mount.
Component Function Check
INFOID:0000000003856836
1.
CHECK OVERALL FUNCTION
1.
Start engine and warm it up to normal operating temperature.
2.
Selector level position is D while depressing the brake pedal and parking brake pedal.
3.
Disconnect electronic controlled engine mount control solenoid valve harness connector.
4.
Check that body vibration increases compared to the condition of step 2 above (with vehicle stopped).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>>
.
Diagnosis Procedure
INFOID:0000000003856837
1.
CHECK VACUUM SOURCE
1.
Turn ignition switch OFF.
2.
Reconnect electronic controlled engine mount control solenoid valve harness connector.
3.
Disconnect vacuum hose connected to electronic controlled engine mount.
4.
Start engine and let it idle.
5.
Check vacuum hose for vacuum existence.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 2.
2.
CHECK VACUUM HOSES AND VACUUM GALLERY
1.
Turn ignition switch OFF.
2.
Check vacuum hoses and vacuum gallery for clogging, cracks or improper connection. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace vacuum hoses and vacuum gallery.
3.
CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE POWER SUPPLY
CIRCUIT
1.
Disconnect electronic controlled engine mount control solenoid valve harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between front electronic controlled engine mount harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Vacuum should exist.
Electronic controlled engine mount
control solenoid valve
Ground
Voltage
Connector
Terminal
F11
1
Ground
Battery voltage
EC-332
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
ELECTRONIC CONTROLLED ENGINE MOUNT
Check the following.
• Harness connectors E6, F123
• 10A fuse (No. 3)
• Fuse block (J/B) E103
• Harness for open or short between electronic controlled engine mount control solenoid valve and fuse
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE OUTPUT SIG-
NAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check the continuity between ECM harness connector and electronic controlled engine mount control
solenoid valve harness connector.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness connectors.
6.
CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE
EC-332, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace electronic controlled engine mount control solenoid valve.
7.
CHECK ELECTRONIC CONTROLLED ENGINE MOUNT
1.
Turn ignition switch OFF.
2.
Install vacuum pump (A) to electronic controlled engine mount
(1).
3.
Check that a vacuum is maintained when applying the vacuum
of -40 kPa (-400 mbar, -300 mmHg, -11.81 inHg) to electronic
controlled engine mount.
4.
Also visually check electronic controlled engine mount.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace electronic controlled engine mount.
8.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace intake manifold collector.
NO
>> Repair or replace malfunctioning part.
Component Inspection
INFOID:0000000003856838
1.
CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE
With CONSULT-III
1.
Turn ignition switch OFF.
2.
Reconnect electronic controlled engine mount control solenoid valve harness connector.
3.
Disconnect vacuum hoses connected to electronic controlled engine mount control solenoid valve.
4.
Turn ignition switch ON.
ECM
Electronic controlled engine
mount control solenoid valve
Continuity
Connector
Terminal
Connector
Terminal
F7
28
F11
2
Existed
MBIB1237E
ELECTRONIC CONTROLLED ENGINE MOUNT
EC-333
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
5.
Select “ENGINE MOUNTING” in “ACTIVE TEST” mode with CONSULT-III.
6.
Check air passage continuity and operation delay time under the
following conditions.
Without CONSULT-III
1.
Turn ignition switch OFF.
2.
Disconnect electronic controlled engine mount control solenoid
valve harness connector.
3.
Disconnect vacuum hoses connected to electronic controlled engine mount control solenoid valve.
4.
Check air passage continuity and operation delay time under the
following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace electronic controlled engine mount control sole-
noid valve.
Condition
(ENGINE MOUNTING)
Air passage continuity
between (A) and (B)
Air passage continuity
between (A) and (C)
TRVL
Existed
Not existed
IDLE
Not existed
Existed
Condition
Air passage continuity
between (A) and (B)
Air passage continuity
between (A) and (C)
12 V direct current supply be-
tween terminals 1 and 2
Existed
Not existed
No supply
Not existed
Existed
JMBIA0180ZZ
PBIB2532E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст