Nissan Teana J32. Manual — part 1261
FRONT WIPER MOTOR GROUND CIRCUIT
WW-29
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000003761592
1.
CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Check continuity between front wiper motor harness connector and ground.
Does continuity exist?
YES
>> Front wiper motor ground circuit is normal.
NO
>> Repair the harness or connector.
Front wiper motor
Ground
Continuity
Connector
Terminal
E12
2
Existed
WW-30
< COMPONENT DIAGNOSIS >
WASHER SWITCH
WASHER SWITCH
Description
INFOID:0000000003761593
Washer switch is integrated with combination switch.
Component Inspection
INFOID:0000000003761594
1.
CHECK WIPER SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect combination switch connector.
3.
Check continuity between the combination switch terminals.
Does continuity exist?
YES
>> Wiper and washer switch is normal.
NO
>> Replace wiper and washer switch.
JPLIA0310ZZ
Combination switch
Condition
Continuity
Terminal
1
6
Front washer switch ON
Existed
HEADLAMP WASHER RELAY
WW-31
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
HEADLAMP WASHER RELAY
Component Inspection
INFOID:0000000003761595
1.
CHECK HEADLAMP WASHER RELAY
1.
Turn the ignition switch OFF.
2.
Remove headlamp washer relay.
3.
Apply battery voltage to headlamp washer relay between terminals 1 and 2.
4.
Check continuity of headlamp washer relay.
Does continuity exist?
YES
>> Headlamp washer relay is normal.
NO
>> Replace headlamp washer relay.
Headlamp washer relay
Condition
Continuity
Terminal
Voltage
3
5
Apply
Existed
Not Apply
Not existed
WW-32
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER CIRCUIT
HEADLAMP WASHER CIRCUIT
Component Function Check
INFOID:0000000003761599
1.
CHECK HEADLAMP WASHER OPERATION
CONSULT-III ACTIVE TEST
1.
Select “HEAD LAMP WASHER” of IPDM E/R active test item.
2.
With operating the test item, check headlamp operation.
Is headlamp washer operation normally?
YES
>> Headlamp washer circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000003761600
1.
CHECK HEADLAMP WASHER FUSIBLE LINK
1.
Turn the ignition switch OFF.
2.
Check that the headlamp washer 40A fusible link (#J) is not fusing.
Is the fusible link fusing?
YES
>> Replace the fusible link after repairing the applicable circuit.
NO
>> GO TO 2.
2.
CHECK HEADLAMP WASHER RELAY POWER SUPPLY
1.
Remove headlamp washer relay.
2.
Check voltage between headlamp washer harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK HEADLAMP WASHER RELAY
Check headlamp washer relay. Refer to
.
Is the headlamp washer relay normal?
YES
>> GO TO 4.
NO
>> Replace headlamp washer relay.
4.
CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OUTPUT
CONSULT-III ACTIVE TEST
1.
Install headlamp washer relay.
2.
Turn the ignition switch ON.
3.
Select “HEAD LAMP WASHER” of IPDM E/R active test item.
4.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
On
:Headlamp washer ON operation
Off
:Stop the headlamp washer.
Terminals
Voltage (Approx.)
(+)
(
−
)
Headlamp washer relay
Ground
Connector
Terminal
E333
2
Battery voltage
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст