Nissan Teana J32. Manual — part 1194
TM-300
< PRECAUTION >
[CVT: RE0F10A]
PRECAUTIONS
• Turn ignition switch OFF and disconnect negative battery
cable before connecting or disconnecting the TCM harness
connector. Because battery voltage is applied to TCM even if
ignition switch is turned OFF.
• When connecting or disconnecting pin connectors into or
from TCM, do not damage pin terminals (bend or break).
Check that there are not any bends or breaks on TCM pin ter-
minal, when connecting pin connectors.
• Perform TCM input/output signal inspection and check
whether TCM functions normally or not before replacing TCM.
Refer to
• Perform “DTC Confirmation Procedure” after performing each
TROUBLE DIAGNOSIS.
If the repair is completed the DTC should not be displayed in
the “DTC Confirmation Procedure”.
• Always use the specified brand of CVT fluid. Refer to
• Use lint-free paper, not cloth rags, during work.
• Dispose of the waste oil using the methods prescribed by law, ordi-
nance, etc. after replacing the CVT fluid.
Service Notice or Precaution
INFOID:0000000003806500
OBD SELF-DIAGNOSIS
• CVT self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the Malfunction Indicator (MI). Refer to the table on
for the indicator used to display each self-diagnostic result.
• The self-diagnostic results indicated by the MI are automatically stored in both the ECM and TCM memories.
Always perform the procedure on
TM-202, "Diagnosis Description"
to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD, refer to
EC-102, "Diagnosis Description"
SEF289H
SEF291H
MEF040DA
SAT652J
PRECAUTIONS
TM-301
< PRECAUTION >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Certain systems and components, especially those related to OBD, may use the new style slide-lock-
ing type harness connector. For description and how to disconnect, refer to
.
ATFTEMP COUNT Conversion Table
INFOID:0000000003806501
ATFTEMP COUNT
Temperature
°
C (
°
F)
ATFTEMP COUNT
Temperature
°
C (
°
F)
4
–30 (–22)
177
90 (194)
8
–20 (–4)
183
95 (203)
13
–10 (14)
190
100 (212)
17
–5 (23)
196
105 (221)
21
0 (32)
201
110 (230)
27
5 (41)
206
115 (239)
32
10 (50)
210
120 (248)
39
15 (59)
214
125 (257)
47
20 (68)
218
130 (266)
55
25 (77)
221
135 (275)
64
30 (86)
224
140 (284)
73
35 (95)
227
145 (293)
83
40 (104)
229
150 (302)
93
45 (113)
231
155 (311)
104
50 (122)
233
160 (320)
114
55 (131)
235
165 (329)
124
60 (140)
236
170 (338)
134
65 (149)
238
175 (347)
143
70 (158)
239
180 (356)
152
75 (167)
241
190 (374)
161
80 (176)
243
200 (392)
169
85 (185)
—
—
TM-302
< PREPARATION >
[CVT: RE0F10A]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000003806502
Commercial Service Tools
INFOID:0000000003806503
Tool number
Tool name
Description
1. ST25054000
Adapter
2. ST25055000
Adapter
Measuring line pressure
KV31103600
Joint pipe adapter
(With ST25054000)
Measuring line pressure
SCIA8372J
ZZA1227D
Tool number
Tool name
Description
Power tool
Loosening nuts and bolts
Oil pressure gauge set
1. Oil pressure gauge
2. Hose
3. Joint pipe
Measuring line pressure
PBIC0190E
SCIA8373J
PREPARATION
TM-303
< PREPARATION >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Drift
a: 54 mm (2.13 in) dia.
b: 47 mm (1.85 in) dia.
Installing differential side oil seal
Drift
a: 65 mm (2.56 in) dia.
b: 60 mm (2.36 in) dia.
Installing converter housing oil seal
Tool number
Tool name
Description
NT115
NT115
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст