Nissan Teana J32. Manual — part 808

CHASSIS MAINTENANCE

MA-41

< ON-VEHICLE MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

DRIVE SHAFT : Inspection

INFOID:0000000003858317

• Check boot and drive shaft for cracks, wear, damage and grease

leakage.

SFA108A

MA-42

< ON-VEHICLE MAINTENANCE >

BODY MAINTENANCE

BODY MAINTENANCE

LOCKS, HINGES AND HOOD LATCH

LOCKS, HINGES AND HOOD LATCH : Lubricating

INFOID:0000000003858318

For hood and hood lock illustration.
• Hood: Refer to

DLK-191, "HOOD ASSEMBLY : Exploded View"

.

• Hood lock control: Refer to

DLK-220, "Exploded View"

.

For door and door lock illustration.
• Front door: Refer to

DLK-201, "DOOR ASSEMBLY : Exploded View"

.

• Front door lock: Refer to

DLK-222, "DOOR LOCK : Exploded View"

.

• Rear door: Refer to

DLK-207, "DOOR ASSEMBLY : Exploded View"

.

• Rear door lock: Refer to

DLK-227, "DOOR LOCK : Exploded View"

.

For trunk lid and trunk lid lock illustration.
• Trunk lid: Refer to

DLK-213, "TRUNK LID ASSEMBLY : Exploded View"

.

• Trunk lid lock: Refer to

DLK-231, "Exploded View"

.

SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS

SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection

INFOID:0000000003858319

For front seat belt illustration. Refer to

SB-5, "SEAT BELT RETRACTOR : Exploded View"

.

For rear seat belt illustration. Refer to

SB-10, "SEAT BELT RETRACTOR : Exploded View"

.

CAUTION:

• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-

wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.

• If any component of seat belt assembly is questionable, do not repair.

Replace as seat belt assembly.

• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to

SB-3, "SEAT BELT RETRACTOR : Inspection"

,

SB-8, "SEAT BELT RETRACTOR :

Inspection"

in SB section.

• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released

BODY CORROSION

BODY CORROSION : Checking Body Corrosion

INFOID:0000000003858320

Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.

HEMMED PANELS

Hood front end, door lower end, trunk lid rear end, etc.

PANEL JOINT

Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.

PANEL EDGE

Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.

PARTS CONTACT

Waist moulding, windshield moulding, bumper, etc.

BODY MAINTENANCE

MA-43

< ON-VEHICLE MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

PROTECTORS

Damage or condition of mudguard, fender protector, chipping protector, etc.

ANTI-CORROSION MATERIALS

Damage or separation of anti-corrosion materials under the body.

DRAIN HOLES

Condition of drain holes at door and side sill. When repairing corroded areas, refer to the Corrosion Repair
Manual.

MA-44

< SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

DRIVE BELTS

DRIVE BELTS : Drive Belt

INFOID:0000000003862442

DRIVE BELT

ENGINE COOLANT

ENGINE COOLANT : Periodical Maintenance Specification

INFOID:0000000003862443

ENGINE COOLANT CAPACITY (APPROXIMATE)

Unit:

(lmp qt)

ENGINE OIL

ENGINE OIL : Periodical Maintenance Specification

INFOID:0000000003862444

ENGINE OIL CAPACITY (APPROXIMATE)

Unit:

(lmp qt)

SPARK PLUG

SPARK PLUG : Spark Plug

INFOID:0000000003862445

SPARK PLUG

Unit: mm (in)

ROAD WHEEL

ROAD WHEEL : Road Wheel

INFOID:0000000003861779

ALUMINUM WHEEL (CONVENTIONAL)

Tension of drive belt

Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.

Engine coolant capacity (With reservoir tank at “MAX” level)

9.1 (8)

Reservoir tank

0.8 (3/4)

Drain and refill

With oil filter change

4.6 (4)

Without oil filter change

4.3 (3-3/4)

Dry engine (Overhaul)

5.3 (4-5/8)

Make

DENSO

Standard type

VQ25DE

FXE20HR11

VQ35DE

FXE22HR11

Gap (Nominal)

Standard

1.1 (0.043)

Limit

1.4 (0.055)

Item

Limit

Radial runout

Lateral deflection

Less than 0.3 mm (0.012 in)

Radial deflection

Allowable unbalance

Dynamic (At flange)

Less than 5 g (0.17 oz) (one side)

Static (At flange)

Less than 10 g (0.35 oz)