Nissan Teana J32. Manual — part 844
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
MWI-119
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000003792607
The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure)
Diagnosis Procedure
INFOID:0000000003792608
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
MWI-32, "Diagnosis Description"
Is oil pressure warning lamp illuminated?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK IPDM E/R OUTPUT VOLTAGE
1.
Disconnect the oil pressure switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between the oil pressure switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CHECK OIL PRESSURE SWITCH UNIT
Perform a unit check for the oil pressure switch. Refer to
MWI-50, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
.
NO
>> Replace oil pressure switch.
4.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
Check the oil pressure switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK COMBINATION METER INPUT SIGNAL
Connect CONSULT-III and perform an input signal check for the combination meter. Refer to
.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
Terminals
Voltage
(Approx.)
(+)
(-)
Oil pressure switch
Ground
Connector
Terminal
F63
1
12 V
MWI-120
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
Description
INFOID:0000000003792609
• The parking brake warning is displayed during vehicle travel even though the parking brake is released
• The parking brake warning is not displayed even though driving the vehicle with the parking brake applied
Diagnosis Procedure
INFOID:0000000003792610
1.
CHECK PARKING BRAKE WARNING LAMP OPERATION
1.
Start engine.
2.
Check the operation of the parking brake warning lamp when operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Check the parking brake switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH UNIT
Perform a unit check for the parking brake switch. Refer to
BRC-124, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace parking brake switch.
Condition
Warning lamp status
When parking brake is applied
ON
When parking brake is released
OFF
MWI
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
MWI-121
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000003792613
• The door ajar warning is displayed even though all of the doors are closed.
• The door ajar warning is not displayed even though a door is ajar.
Diagnosis Procedure
INFOID:0000000003792614
1.
CHECK BCM INPUT/OUTPUT SIGNAL
Connect CONSULT-III and check the BCM input signals. Refer to
DLK-57, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “DOOR W/L” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
3.
CHECK DOOR SWITCH SIGNAL CIRCUIT
Check the door switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK DOOR SWITCH UNIT
Perform a unit check for the door switch. Refer to
DLK-59, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace applicable door switch. Refer to
DLK-234, "Removal and Installation"
“DOOR W/L”
Door open
: On
Door closed
: Off
MWI-122
< SYMPTOM DIAGNOSIS >
THE TRUNK OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
THE TRUNK OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000003795430
• The trunk ajar warning is displayed continuously even though the trunk lid is closed.
• The trunk ajar warning is not displayed even though the trunk lid is open.
Diagnosis Procedure
INFOID:0000000003795431
1.
CHECK BCM INPUT/OUTPUT SIGNAL
Connect CONSULT-III and check the BCM input signals. Refer to
DLK-70, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “TRUNK/GLAS-H” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM.
3.
CHECK TRUNK LID OPENER SWITCH SIGNAL CIRCUIT
Check the trunk lid opener switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK TRUNK LID OPENER SWITCH UNIT
Perform a unit check for the trunk lid opener switch. Refer to
DLK-71, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace the trunk lid switch. Refer to
DLK-243, "Removal and Installation"
“TRUNK/GLAS-H”
Trunk lid open
: On
Trunk lid closed
: Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст