Nissan Teana J32. Manual — part 490
EM-84
< DISASSEMBLY AND ASSEMBLY >
CAMSHAFT
CAMSHAFT
Exploded View
INFOID:0000000003802283
Removal and Installation
INFOID:0000000003802284
REMOVAL
1.
Remove front timing chain case, camshaft sprocket, timing chain and rear timing chain case. Refer to
1.
Camshaft bracket (No. 3, 4)
2.
Camshaft bracket (No. 2)
3.
Seal washer
4.
Camshaft bracket (No. 1)
5.
Dowel pin
6.
Camshaft (EXH) (bank 1)
7.
Camshaft (INT) (bank 1)
8.
Valve lifter
9.
Timing chain tensioner (secondary)
(bank 1)
10. Spring
11.
Plunger
12.
Timing chain tensioner (secondary)
(bank 2)
13. Cylinder head (bank 2)
14.
Dowel pin
15. Camshaft sensor bracket
16. Camshaft (EXH)
17.
Camshaft signal plate (INT)
18. Camshaft (INT)
19. Cylinder head (bank 1)
20.
Camshaft signal plate (INT)
21. Camshaft sensor bracket
A.
Refer to
Refer to
for symbols in the figure.
JPBIA1719GB
CAMSHAFT
EM-85
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Loosen camshaft sensor bracket bolts in reverse order as
shown in the figure.
NOTE:
The order of loosening bolts in the same for bank 1 and bank 2.
3.
Remove camshaft brackets.
• Mark camshafts, camshaft brackets and bolts so they are placed in the same position and direction for
installation.
• Equally loosen camshaft bracket bolts in several steps in
reverse order as shown in the figure.
4.
Remove camshafts.
5.
Remove valve lifters.
• Identify installation positions, and store them without mixing them up.
6.
Remove timing chain tensioners (secondary) (1) from cylinder
head.
• Remove timing chain tensioner (secondary) with its stopper
pin (C) attached.
NOTE:
Stopper pin should be attached when timing chain (secondary)
is removed.
INSTALLATION
: Engine front
JPBIA1960ZZ
: Engine front
JPBIA0257ZZ
A
: Bank 1
B
: Bank 2
JPBIA0121ZZ
EM-86
< DISASSEMBLY AND ASSEMBLY >
CAMSHAFT
1.
Install timing chain tensioners (secondary) (1) on both sides of
cylinder head.
• Install timing chain tensioner (secondary) with its stopper pin
(C) attached.
• Install timing chain tensioner (secondary) with sliding part fac-
ing downward on cylinder head (bank 1), and with sliding part
facing upward on cylinder head (bank 2).
2.
Install valve lifters.
• Install it in the original position.
3.
Install camshafts.
• Follow your identification marks made during removal, or fol-
low the identification marks that are present on new camshafts
for proper placement and direction.
VQ25DE
VQ35DE
• Install camshaft so that dowel pin (A) on front end face are
positioned as shown in the figure. (No. 1 cylinder TDC on its
compression stroke)
NOTE:
Though camshaft does not stop at the portion as shown in the
figure, for the placement of cam nose, it is generally accepted
camshaft is placed for the same direction of the figure.
4.
Install camshaft brackets.
A
: Bank 1
B
: Bank 2
JPBIA0121ZZ
: Engine front
JPBIA1749ZZ
Bank
INT/EXH
Dowel pin (1)
Paint marks
M1 (D)
M2 (E)
M3 (C)
1
EXH (B)
Yes
No
Purple
Light blue
INT (A)
Yes
Yellow
No
Light blue
2
INT (A)
Yes
Yellow
No
Light blue
EXH (B)
Yes
No
Purple
Light blue
Bank
INT/EXH
Dowel pin (1)
Paint marks
M1 (D)
M2 (E)
M3 (C)
1
EXH (B)
Yes
No
Light blue
Light blue
INT (A)
Yes
Pink
No
Light blue
2
INT (A)
Yes
Pink
No
Light blue
EXH (B)
Yes
No
Light blue
Light blue
JPBIA2368ZZ
CAMSHAFT
EM-87
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Remove foreign material completely from camshaft bracket backside and from cylinder head installation
face.
• Install camshaft bracket in original position and direction as
shown in the figure.
• Install camshaft brackets (No. 2 to 4) aligning the stamp marks
(A) as shown in the figure.
NOTE:
There are no identification marks indicating left and right for
camshaft bracket (No. 1).
• Apply liquid gasket to mating surface of camshaft bracket (No.
1) as shown on bank 1 and bank 2.
Use Genuine Liquid Gasket or equivalent.
A
: No. 1
B
: No. 2
C
: No. 3
D
: No. 4
E
: Bank 1
F
: Exhaust side
G
: Intake side
H
: Bank 2
I
: Intake side
J
: Exhaust side
: Engine front
JPBIA0258ZZ
B
: Bank 1
C
: Bank 2
: Engine front
JPBIA0272ZZ
a
: 8.5 mm (0.335 in)
b
: 2 mm (0.08 in)
c
: Clearance 5 mm (0.20 in)
d
:
φ
2.0 - 2.3 mm (0.08 - 0.12 in)
*
: Apply liquid gasket to rear timing chain case side
JPBIA0255ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст