Nissan Teana J32. Manual — part 961
REAR LOWER LINK & COIL SPRING
RSU-9
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Install coil spring by aligning lower end of the coil spring to step (A)
between rubber seat (1) and rear lower link (2).
CAUTION:
Set coil spring so that its paint marks are aligned with the
positions of 3.0 turns (2 places) and 4.0 turns (1 place) or 4.0
turns (2 places) and 5.0 turns (1 place) from the bottom end of
the coil spring.
• Perform the final tightening of rear suspension member and axle
installation position (rubber bushing) under unladen condition with
tires on level ground.
Inspection
INFOID:0000000003811144
INSPECTION AFTER REMOVAL
Check lower link, bushing and coil spring for deformation, crack, and damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor (with VDC). Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
JPEIB0122ZZ
RSU-10
< ON-VEHICLE REPAIR >
REAR SHOCK ABSORBER
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000003811145
Removal and Installation
INFOID:0000000003811146
REMOVAL
1.
Remove tires.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-58, "REAR WHEEL SENSOR : Exploded View"
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
3.
Separate stabilizer connecting rod (lower side). Refer to
4.
Set suitable jack under axle housing to relieve the coil spring tension.
5.
Remove shock absorber mounting bolt (lower side).
6.
Gradually lower the jack to remove it from rear axle.
7.
Remove shock absorber mounting nuts (upper side) (
), and
remove shock absorber assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000003811147
INSPECTION AFTER REMOVAL
1.
Shock absorber
2.
Bound bumper
3.
Shock absorber mounting bracket
4.
Mounting seal
5.
Cap
Refer to
for symbols in the figure.
JPEIB0123GB
JPEIB0111ZZ
REAR SHOCK ABSORBER
RSU-11
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Check the following items, and replace the if necessary.
• Shock absorber for deformation, cracks, damage.
• Welded and sealed areas for oil leakage.
• Piston rod for damage, uneven wear or distortion.
• Seal of shock absorber mounting bracket for cracks, damage and come off.
INSPECTION AFTER INSTALLATION
Check wheel sensor harness for proper connection. Refer to
BRC-58, "REAR WHEEL SENSOR : Exploded
(without VDC),
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
RSU-12
< ON-VEHICLE REPAIR >
RADIUS ROD
RADIUS ROD
Exploded View
INFOID:0000000003811148
Removal and Installation
INFOID:0000000003811149
REMOVAL
1.
Remove tire.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-58, "REAR WHEEL SENSOR : Exploded View"
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
3.
Remove rear lower link and coil spring. Refer to
4.
Remove shock absorber mounting bolt (lower side). Refer to
.
5.
Remove front lower link mounting bolt and nut (axle housing side). Refer to
6.
Loosen front lower link mounting bolt and nut (suspension member side). Refer to
.
7.
Remove radius rod mounting bolts and nuts (axle housing side).
8.
Remove radius rod mounting bolt (rear suspension member side), and then remove radius rod.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000003811150
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
2.
Check wheel alignment. Refer to
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0108GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст