Qashqai J11. Wiper & washer — part 2
SYSTEM
WW-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LOW).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HIGH) to IPDM E/R via CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper HI/LO relay according to the front
wiper request signal (HIGH).
FRONT WIPER AUTO OPERATION
Rain Detection
Rain level and sensor conditions are detected by light & rain sensor.
• BCM transmits the vehicle conditions (vehicle speed, front wiper condition, light & rain sensor sensitivity set-
ting, etc.) to the light & rain sensor via the light & rain sensor serial link.
• Light & rain sensor judges a wiping speed for front wiper by rain condition and the vehicle conditions. And it
transmits the wiping speed request signal to the BCM via the light & rain sensor serial link.
Auto Wiping Operation
• BCM receives the wiping speed request signal from the light & rain sensor via the light & rain sensor serial
link.
• BCM controls front wiper operation according to the wiping speed request signal. And it transmits the front
wiper request signal (LOW or HIGH) to the IPDM E/R via CAN communication line.
Front wiper AUTO operating condition
- Ignition switch ON
- Front wiper switch AUTO
NOTE:
When the front wiper switch is turned to AUTO position, front wiper operates once regardless of rainy condi-
tions.
Light & rain Sensor Sensitivity Setting
BCM determines light & rain sensor sensitivity according to wiper volume dial position.
NOTE:
Factory setting of the light & rain sensor operation is operation linked with light & rain sensor. Light & rain sen-
sor operation can be set to operation linked or not linked with light & rain sensor using CONSULT. Refer to
WW-23, "WIPER : CONSULT Function - WIPER"
.
NOTE:
When the wiper volume dial position is turned up by 1 level under front wiper AUTO operating condition, front
wiper operates once.
Splash mode operation
Front wiper is operated at HI regardless of the wiper volume adjustment position, when water drops are instan-
taneously sprayed over the windshield glass due to water splash from oncoming vehicles or other causes.
After that, AUTO operation is performed depending on the amount of water drops.
SPLASH MODE OPERATION CONDITIONS
Wiper volume dial position
Sensitivity
1
Low sensitivity
2
Low
−
medium sensitivity
3
Medium
−
high sensitivity
4
High sensitivity
WW-12
< SYSTEM DESCRIPTION >
SYSTEM
• Front wiper switch AUTO
• Ignition switch ON
NOTE:
Splash mode is not operated and auto wiping operation is performed, while the vehicle is stopped.
FRONT WIPER AUTO STOP OPERATION
• BCM transmits the front wiper request signal (RETURN) to IPDM E/R via CAN communication when the
front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor to find out the front wiper
motor position (stop position/except stop position).
• When IPDM E/R receives the front wiper request signal (RETURN) from BCM and the front wiper motor
position is not in the stop position, IPDM E/R turns ON the front wiper relay until the front wiper motor returns
to the stop position.
• When the front wiper motor returns to the stop position, IPDM E/R transmits front wiper status signal to BCM
via CAN communication.
• When BCM receives front wiper status signal from IPDM, BCM transmits the front wiper request signal
(STOP) to IPDM E/R via CAN communication.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LOW) so that the front wiper operates approximately 2 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LOW).
• For models without around view monitor: The washer pump is grounded through the combination switch with
the front washer switch ON.
• For models with around view monitor: Pump control unit detects front window washer switch signal from
combination switch and controls the washer pump.
FRONT WIPER DROP WIPE OPERATION
• BCM controls the front wiper to operate once according to the conditions of front wiper drop wipe operation.
Front wiper drop wipe operating condition
- Ignition switch ON
- Front wiper switch OFF
- Front washer switch OFF
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication so that the front
wiper operates once at 3 seconds after front wiper operation linked with washer.
NOTE:
Factory setting of the front wiper drop wipe operation is ON. Front wiper drop wipe operation can be set to ON
or OFF using CONSULT. Refer to
WW-23, "WIPER : CONSULT Function - WIPER"
FRONT WIPER SERVICE POSITION OPERATION
• Front wiper operates at LO and stops so that front wiper can be locked back without interfere the hood.
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication for 0.6 seconds
according to the conditions of front wiper service position operation.
Front wiper service position operation conditions (Within 1 minute after turning ignition switch Off)
- Front wiper switch is OFF
- Front wiper is in stop position
- Front wiper switch MIST is operated 2 times (Within 0.47 second)
Front wiper service position operation conditions (During ignition switch is On)
- Front wiper switch is OFF
- Front wiper is in stop position
- Vehicle speed is less than 4 km/h
- Front wiper switch MIST is operated 2 times (Within 0.47 second)
• After the front wiper LO operation, IPDM receives the front wiper request signal (STOP) from BCM and then
stops the front wiper.
SYSTEM
WW-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• Front wiper returns to stop position when front wiper switch is operated. (If 1 minute or more is passed after
turning ignition switch OFF, front wiper returns to stop position when ignition switch is turned ON and front
wiper switch is operated.)
FRONT WIPER AND WASHER SYSTEM (WITH LIGHT & RAIN SENSOR) : Fail-safe
INFOID:0000000010430959
IPDM E/R
If No CAN Communication Is Available With BCM
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
Front Wiper Protection Function
IPDM E/R detects front wiper stop position by front wiper stop position signal.
When front wiper stop position signal is in the condition listed below while the front wiper is operating, IPDM E/
activates the fail-safe.
BCM
Fail-safe Control By Light & Rain Sensor Malfunction
BCM detects the light & rain sensor serial link error and the light & rain sensor malfunction.
BCM controls the following fail-safe when light & rain sensor has a malfunction.
• Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is main-
tained until the front wiper switch is turned OFF.
• Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is
turned off.
FRONT WIPER AND WASHER SYSTEM (WITHOUT LIGHT & RAIN SENSOR)
FRONT WIPER AND WASHER SYSTEM (WITHOUT LIGHT & RAIN SENSOR) : Sys-
tem Description
INFOID:0000000010430960
SYSTEM DIAGRAM
Control part
Fail-safe operation
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is turned
OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is ac-
tivated while the front wiper is set in the AUTO mode and the front wiper motor is operating.
Ignition switch
Front wiper switch
Front wiper stop position signal
Fail-safe
ON
OFF
The signal does not change from the battery
voltage for 10 seconds.
Stops front wiper power supply
for 20 seconds
Except OFF
The signal does not change for 10 seconds.
WW-14
< SYSTEM DESCRIPTION >
SYSTEM
Without Around View Monitor
With Around View Monitor
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R via CAN communication depending on each oper-
ating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper HI/LO relay according to the
front wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LOW).
FRONT WIPER HI OPERATION
JMLIA5154GB
JMLIA5155GB
SYSTEM
WW-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• BCM transmits the front wiper request signal (HIGH) to IPDM E/R via CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper HI/LO relay according to the front
wiper request signal (HIGH).
FRONT WIPER INT OPERATION
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication depending on the
front wiper INT operating condition and intermittent operation delay interval according to the wiper volume
dial position.
Front wiper INT operating condition
- Ignition switch ON
- Front wiper switch INT
• IPDM E/R turns ON the integrated front wiper relay so that the front wiper is operated only once according to
the front wiper request signal (LOW) and front wiper request signal (RETURN).
• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop
position signal received from IPDM E/R via CAN communication.
• BCM transmits the front wiper request signal (LOW) again after the intermittent operation delay interval.
NOTE:
Front wiper INT operation can be set to operation linked or not linked with vehicle speed using CONSULT.
Refer to
WW-23, "WIPER : CONSULT Function - WIPER"
Front wiper intermittent operation with vehicle speed
• BCM calculates the intermittent operation delay interval from the following
- Vehicle speed signal
- Wiper volume dial position
Intermittent operation delay Interval
Unit: Second
*: When operation setting is not linked with vehicle speed.
FRONT WIPER AUTO STOP OPERATION
• BCM transmits the front wiper request signal (RETURN) to IPDM E/R via CAN communication when the
front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor to find out the front wiper
motor position (stop position/except stop position).
• When IPDM E/R receives the front wiper request signal (RETURN) from BCM and the front wiper motor
position is not in the stop position, IPDM E/R turns ON the front wiper relay until the front wiper motor returns
to the stop position.
• When the front wiper motor returns to the stop position, IPDM E/R transmits front wiper status signal to BCM
via CAN communication.
• When BCM receives front wiper status signal from IPDM, BCM transmits the front wiper request signal
(STOP) to IPDM E/R via CAN communication.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LOW) so that the front wiper operates approximately 2 times
when the front washer switch OFF is detected.
Wiper volume dial
position
Intermittent
operation
interval
Vehicle speed
0 – 5 km/h
(0 – 3.1 MPH)
5 – 65 km/h
(3.1 – 40.4 MPH)*
65 km/h
(40.4 MPH) or more
1
Long
↑
↓
Short
62.5
25
15
2
31.25
12.5
7.5
3
18.75
7.5
4.5
4
12.5
5
3
5
6.25
2.5
1.5
WW-16
< SYSTEM DESCRIPTION >
SYSTEM
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LOW).
• For models without around view monitor: The washer pump is grounded through the combination switch with
the front washer switch ON.
• For models with around view monitor: Pump control unit detects front window washer switch signal from
combination switch and controls the washer pump.
FRONT WIPER DROP WIPE OPERATION
• BCM controls the front wiper to operate once according to the conditions of front wiper drop wipe operation.
Front wiper drop wipe operating condition
- Ignition switch ON
- Front wiper switch OFF
- Front washer switch OFF
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication so that the front
wiper operates once at 3 seconds after front wiper operation linked with washer.
NOTE:
Factory setting of the front wiper drop wipe operation is ON. Front wiper drop wipe operation can be set to ON
or OFF using CONSULT. Refer to
WW-23, "WIPER : CONSULT Function - WIPER"
FRONT WIPER SERVICE POSITION OPERATION
• Front wiper operates at LO and stops so that front wiper can be locked back without interfere the hood.
• BCM transmits the front wiper request signal (LOW) to IPDM E/R via CAN communication for 0.6 seconds
according to the conditions of front wiper service position operation.
Front wiper service position operation conditions (Within 1 minute after turning ignition switch Off)
- Front wiper switch is OFF
- Front wiper is in stop position
- Front wiper switch MIST is operated 2 times (Within 0.47 second)
Front wiper service position operation conditions (During ignition switch is On)
- Front wiper switch is OFF
- Front wiper is in stop position
- Vehicle speed is less than 4 km/h
- Front wiper switch MIST is operated 2 times (Within 0.47 second)
• After the front wiper LO operation, IPDM receives the front wiper request signal (STOP) from BCM and then
stops the front wiper.
• Front wiper returns to stop position when front wiper switch is operated. (If 1 minute or more is passed after
turning ignition switch OFF, front wiper returns to stop position when ignition switch is turned ON and front
wiper switch is operated.)
FRONT WIPER AND WASHER SYSTEM (WITHOUT LIGHT & RAIN SENSOR) : Fail-
Safe
INFOID:0000000010430962
IPDM E/R
If No CAN Communication Is Available With BCM
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
Front Wiper Protection Function
IPDM E/R detects front wiper stop position by front wiper stop position signal.
When front wiper stop position signal is in the condition listed below while the front wiper is operating, IPDM E/
activates the fail-safe.
Control part
Fail-safe operation
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is turned
OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is ac-
tivated while the front wiper is set in the AUTO mode and the front wiper motor is operating.
SYSTEM
WW-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER AND WASHER SYSTEM
REAR WIPER AND WASHER SYSTEM : System Description
INFOID:0000000010430999
SYSTEM DIAGRAM
Without Around View Monitor
With Around View Monitor
OUTLINE
The rear wiper is controlled by each function of BCM.
Control by BCM
• Combination switch reading function
• Rear wiper control function
REAR WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM controls the rear wiper to start or stop.
REAR WIPER ON OPERATION
• BCM supplies power to the rear wiper motor according to the rear wiper ON operating condition.
Rear wiper ON operating condition
Ignition switch
Front wiper switch
Front wiper stop position signal
Fail-safe
ON
OFF
The signal does not change from the battery
voltage for 10 seconds.
Stops front wiper power supply
for 20 seconds
Except OFF
The signal does not change for 10 seconds.
JMLIA5362GB
JMLIA5394GB
WW-18
< SYSTEM DESCRIPTION >
SYSTEM
- Ignition switch ON
- Rear wiper switch ON
REAR WIPER INT OPERATION
• BCM supplies power to the rear wiper motor according to the INT operating condition.
Rear wiper INT operating condition
- Ignition switch ON
- Rear wiper switch INT
• BCM controls the rear wiper to operate once.
• BCM detects the rear wiper motor stop position.
• BCM supplies power to the rear wiper motor after an intermittent from the stop of the rear wiper motor.
REAR WIPER AUTO STOP OPERATION
• BCM stops supplying power to the rear wiper motor when the rear wiper switch is turned OFF.
• BCM reads a rear wiper stop position signal from the rear wiper motor to detect a rear wiper motor position.
• When the rear wiper motor is at other than the stopping position, BCM continues to supply power to the rear
wiper motor until it returns to the stop position.
NOTE:
BCM stops supplying power to the rear wiper motor when the ignition switch is turned OFF.
REAR WIPER OPERATION LINKED WITH WASHER
• BCM supplies power to the rear wiper motor according to the washer linked operating condition of rear
wiper. When the rear washer switch is turned OFF, BCM controls rear wiper to operate approximately 3
times.
Washer linked operating condition of rear wiper
- Ignition switch ON
- Rear washer switch ON (0.4 second or more)
• For models without around view monitor: The washer pump is grounded through the combination switch with
the rear washer switch ON.
• For models with around view monitor: Pump control unit detects rear window washer switch signal from
combination switch and controls the washer pump.
REAR WIPER DROP WIPE OPERATION
• BCM controls the rear wiper to operate once according to the rear wiper drop wipe operating condition.
JPLIA1258GB
JPLIA1259GB
SYSTEM
WW-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Rear wiper drop wipe operating condition
- Ignition switch ON
- Rear wiper switch OFF
- Rear washer switch OFF
• BCM controls the rear wiper so that it operates once time approximately 3 seconds later after the washer
interlocking operation of the rear wiper.
NOTE:
Rear wiper drop wipe operation can be set to ON or OFF using CONSULT. Refer to
REAR WIPER OPERATION LINKED WITH REVERSE
• BCM controls rear wiper to operate once according to the conditions of rear wiper operation linked with
reverse.
Condition of rear wiper operation linked with reverse
- Ignition switch ON
- Front wiper switch: LO, HI, INT or AUTO
- Rear wiper switch OFF
- Shift position: “R”
• When shift position is “R”, BCM receives reverse switch signal from IPDM E/R via CAN communication, and
then operates rear wiper motor.
NOTE:
Rear wiper operation linked with reverse can be set to ON or OFF using CONSULT. Refer to
.
REAR WIPER AND WASHER SYSTEM : Fail-safe
INFOID:0000000010431001
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1.
More than 1 minute is passed after the rear wiper stop.
2.
Turn rear wiper switch OFF.
3.
Operate the rear wiper switch or rear washer switch.
HEADLAMP WASHER SYSTEM
HEADLAMP WASHER SYSTEM : System Description
INFOID:0000000010430963
SYSTEM DIAGRAM
Except For Russia
JMLIA0559GB
WW-20
< SYSTEM DESCRIPTION >
SYSTEM
For Russia
OUTLINE
Headlamp washer is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Headlamp washer control function
Control by IPDM E/R
• Headlamp washer relay control function
HEADLAMP WASHER OPERATION
Except For Russia
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the headlamp washer request signal to IPDM E/R using CAN communication depending on
each operating condition of the headlamp washer.
Operate by front washer switch at the first time
- Ignition switch ON
- Headlamps ON
- Front washer switch ON at first time
Operate by front washer switch from the second time
- Ignition switch ON
- Headlamps ON
- Front washer switch ON at fifth time after the first time
• IPDM E/R turns ON/OFF the headlamp washer relay by receiving the headlamp washer request signal, and
controls the headlamp washer.
For Russia
JMLIA5327GB
JMLIA2363GB
SYSTEM
WW-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the headlamp washer request signal to IPDM E/R using CAN communication depending on
each operating condition of the headlamp washer.
Operate by headlamp washer switch
- Ignition switch ON
- Headlamps ON
- Headlamp washer switch ON
• IPDM E/R turns ON/OFF the headlamp washer relay by receiving the headlamp washer request signal, and
controls the headlamp washer.
WW-22
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010503209
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
—
AIR CONDITONER*
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
DIAGNOSIS SYSTEM (BCM)
WW-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000010430967
WORK SUPPORT
*
1
: For models without light & rain sensor
*
2
: For models with light & rain sensor
*
3
: Factory setting for Europe, Russia or South Africa
*
4
: Factory setting except for Europe, Russia or South Africa
*
5
: Factory setting for all destination
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT screen item
Indication/Unit
Description
BATTERY VOLTAGE
V
Battery voltage of the moment a particular DTC is detected.
VEHICLE SPEED
km/h
Vehicle speed of the moment a particular DTC is detected.
EXTERNAL TEMP
°
C
External temperature of the moment a particular DTC is detected
VEHICLE COND
—
NOTE:
This item is displayed, but cannot be use this item.
DOOR LOCK STATUS
—
NOTE:
This item is displayed, but cannot be use this item.
POWER SUPPLY
COUNTER
min
Displays the cumulative time from the time that the battery terminal is connected.
Service item
Setting item
Description
WIPER SPEED SET-
TING*
1
On*
3
Linked with vehicle speed
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position.)
The setting of front wiper
INT operation can be
changed.
Off*
4
Not linked with vehicle speed
(Front wiper intermittent time linked with the wiper volume dial
position.)
RAIN SENSOR*
2
On*
5
Linked with light & rain sensor
(Front wiper intermittent time linked with the light & rain sensor,
vehicle speed, and wiper volume dial position)
The setting of front wiper
AUTO operation can be
changed
Off
Not linked with light & rain sensor
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position)
FR RR DRIP
On*
5
Front wiper drop wipe and rear wiper drop wipe operation ON
The setting of drop wipe
operation can be
changed
Off
Front wiper drop wipe and rear wiper drop wipe operation OFF
REAR WIPER LINK
WITH REVERSE
SETTING
On
Rear wiper operation linked with reverse ON
The setting of rear wiper
operation linked with re-
verse can be changed
Off*
5
Rear wiper operation linked with reverse OFF
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication.
WW-24
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*: For models without headlamp washer switch, this item is indicated but is not used.
ACTIVE TEST
*: For models without headlamp washer, this item is indicated but is not used.
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Displays the status of the rear wiper stop position signal received from rear wiper motor.
H/L WSR SW*
[Off/On]
Status of headlamp washer switch judged by BCM.
RAIN SENSOR
[OFF/LOW/HIGH/SPLASH/NG]
Request signal from rain sensor detected by BCM is displayed.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Operates the front wiper HI operation.
Lo
Operates the front wiper LO operation.
INT
Operates the front wiper INT/AUTO operation.
Off
Stops the front wiper operation.
RR WIPER
On
Operates the rear wiper operation.
Off
Stops the rear wiper operation.
HEADLAMP WASHER*
On
Operates the headlamp washer operation.
DIAGNOSIS SYSTEM (IPDM E/R)
WW-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000010503210
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
.
Freeze Frame Data (FFD)
The IPDM E/R records the vehicle condition at the time a particular DTC is detected, and displays on CON-
SULT.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnosis mode
Description
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Work Support
Changes the setting for each system function.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
Ecu Identification
Allows confirmation of IPDM E/R part number.
Configuration
• Read and save the vehicle specification.
• White the vehicle specification when replacing IPDM E/R.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
Description
REVERSE SIGNAL
[Open/Close]
Displays the status of the transmission range switch (CVT) or reverse/neutral position
switch (M/T) judged by IPDM E/R.
IGN RELAY
[Open/Close]
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Open/Close]
Displays the status of the push-button ignition switch judged by IPDM E/R.
NEUTRAL SW
[Open/Close]
Displays the status of the reverse/neutral position switch (M/T) judged by IPDM E/R.
INTERLOCK/PNP SW
[Open/Close]
Displays the status of the transmission range switch (CVT) judged by IPDM E/R.
OIL PRESSURE SW
[Open/Close]
Displays the status of the oil pressure switch judged by IPDM E/R.
LED H/L RH STATUS
[Open/Close]
Displays the LED headlamp (right) ON/OFF status judged by IPDM E/R.
NOTE:
This item is monitored only on the vehicle with LED headlamp.
LED H/L LH STATUS
[Open/Close]
Displays the LED headlamp (left) ON/OFF status judged by IPDM E/R.
NOTE:
This item is monitored only on the vehicle with LED headlamp.
HOOD SW
[Open/Close]
Displays the status of the hood switch judged by IPDM E/R.
COMPRESSOR
[Off/On]
Displays the compressor drive status judged by IPDM E/R.
H/L WASHER PUMP
[Off/On]
Displays the status of the headlamp washer pump judged by IPDM E/R.
WW-26
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
HORN RELAY
[Off/On]
NOTE:
The item is indicated, but not monitored.
COOLING FAN
[Off/On]
NOTE:
The item is indicated, but not monitored.
FRONT WIPER HI/LO RELAY
[Off/On]
Displays the status of the front wiper HI/LO relay judged by IPDM E/R.
FRONT WIPER RELAY
[Off/On]
Displays the status of the front wiper relay judged by IPDM E/R.
IGN RELAY OFF STATUS
[Off/On]
Displays the status of the ignition relay OFF circuit judged by IPDM E/R.
IGN RELAY ON STATUS
[Off/On]
Displays the status of the ignition relay ON circuit judged by IPDM E/R.
STEERING LOCK PWR SPLY
[Off/On]
Displays the power supply status from IPDM E/R to the steering lock unit.
NOTE:
This item is monitored only on the vehicle with Intelligent Key system
HEIGHT SENSOR PWR SPLY
[Off/On]
Displays the power supply status from IPDM E/R to the height sensor.
COOLING FAN RELAY 1
[Open/Close]
Displays the status of the cooling fan relay-1 judged by IPDM E/R.
STARTER RELAY
[Off/On]
Displays the status of the starter control relay judged by IPDM E/R.
COMP ECV DUTY
[%]
Displays the compressor control signal (PWM) status of IPDM E/R.
COOLING FAN RELAY 2
[%]
Displays the status of the cooling fan relay-2 judged by IPDM E/R.
FR FOG LAMP LH
[%]
Displays the front fog lamp (left) output (PWM) status of IPDM E/R.
FR FOG LAMP RH
[%]
Displays the front fog lamp (right) output (PWM) status of IPDM E/R.
LEVELIZER OUTPUT
[%]
Displays the aiming motor drive signal (PWM) status of IPDM E/R.
PARKING LAMP
[%]
Displays the parking lamp output (PWM) status of IPDM E/R.
TAIL LAMP LH
[%]
Displays the tail lamp (left) output (PWM) status of IPDM E/R.
TAIL LAMP RH
[%]
Displays the tail lamp (right) output (PWM) status of IPDM E/R.
DAYTIME RUNNING LIGHT LH
[%]
Displays the daytime running light (left) output status of IPDM E/R.
DAYTIME RUNNING LIGHT RH
[%]
Displays the daytime running light (right) output status of IPDM E/R.
HEADLAMP (HI) LH
[%]
Displays the headlamp (HI) (left) output (PWM) status of IPDM E/R.
HEADLAMP (HI) RH
[%]
Displays the headlamp (HI) (right) output (PWM) status of IPDM E/R.
HEADLAMP (LO) LH
[%]
Displays the headlamp (LO) (left) output (PWM) status of IPDM E/R.
HEADLAMP (LO) RH
[%]
Displays the headlamp (LO) (right) output (PWM) status of IPDM E/R.
A/C RELAY STUCK
[OK/NG]
Displays the ON stuck status of the A/C relay judged by IPDM E/R.
Monitor Item
[Unit]
Description
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст