Nissan Tiida C11. Manual — part 1202
SRC-36
< COMPONENT DIAGNOSIS >
B1182 - B1185 LAP SEAT BELT PRE-TENSIONER
B1182 - B1185 LAP SEAT BELT PRE-TENSIONER
Description
INFOID:0000000001404240
DTC B1182 – B1185 LAP SEAT BELT PRE-TENSIONER
The lap seat belt pre-tensioner is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the lap seat belt pre-tensioner.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000001404241
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.
DTC
If DTC is detected. Refer to
SRC-37, "Diagnosis Procedure (Component diagnosis)"
.
>> END
CONSULT-III name
DTC
DTC detecting condition
Repair order
PRE-TEN2 FRONT LH
[OPEN]
B1182
Lap seat belt pre-tensioner circuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the front lap seat belt pre-tensioner.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
PRE-TEN2 FRONT LH
[VB-SHORT]
B1183
Lap seat belt pre-tensioner circuit is short-
ed to a power supply circuit.
PRE-TEN2 FRONT LH
[GND-SHORT]
B1184
Lap seat belt pre-tensioner circuit is short-
ed to ground.
PRE-TEN2 FRONT LH
[SHORT]
B1185
Lap seat belt pre-tensioner circuits are
shorted to each other.
ALHIA0070GB
B1182 - B1185 LAP SEAT BELT PRE-TENSIONER
SRC-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000001404242
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
LAP SEAT BELT PRE-TENSIONER
Replace the lap seat belt pre-tensioner. Refer to
SB-6, "Removal and Installation of Front Seat Belt"
.
>> GO TO 4
4.
AIR BAG DIAGNOSIS SENSOR UNIT
SRC-38
< COMPONENT DIAGNOSIS >
B1182 - B1185 LAP SEAT BELT PRE-TENSIONER
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 5
5.
RELATED HARNESS
Replace the related harness.
>> END
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
SRC-39
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
Description
INFOID:0000000001396386
DTC B1081 – B1084 SEAT BELT PRE-TENSIONER RH
The seat belt pre-tensioner RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner RH.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000001396387
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.
DTC
If DTC is detected. Refer to
SRC-40, "Diagnosis Procedure (Component diagnosis)"
.
>> END
CONSULT-III name
DTC
DTC detecting condition
Repair order
PRE-TEN FRONT RH
[OPEN]
B1081
RH seat belt pre-tensioner circuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the front RH seat belt pre-tensioner.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
PRE-TEN FRONT RH
[VB-SHORT]
B1082
RH seat belt pre-tensioner circuit is short-
ed to a power supply circuit.
PRE-TEN FRONT RH
[GND-SHORT]
B1083
RH seat belt pre-tensioner circuit is short-
ed to ground.
PRE-TEN FRONT RH
[SHORT]
B1084
RH seat belt pre-tensioner circuits are
shorted to each other.
WHIA0262E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст