Nissan Tiida C11. Manual — part 1058
LU-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR18DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit
INFOID:0000000001337830
OIL PRESSURE
Oil Capacity
Unit:
(Imp qt)
Engine speed rpm
Approximate discharge pressure kPa (bar, kg/cm
2
, psi)
Idle speed
2,000
71.5 (0.70, 0.70, 10)
200 (2.0, 2.0, 29)
Drain and refill
With oil filter change
Approximately 4.4 (3 7/8)
Without oil filter change
Approximately 4.2 (3 3/4)
Dry engine (engine overhaul)
Approximately 5.5 (4 7/8)
PRECAUTIONS
LU-23
< PRECAUTION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001516582
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Liquid Gasket
INFOID:0000000001381534
REMOVAL OF LIQUID GASKET
• After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap (1) the tool into place and slide (2) side-to-side.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
PBIC0275E
PBIC0003E
LU-24
< PRECAUTION >
[K9K]
PRECAUTIONS
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
• If there is a groove for the liquid gasket application, apply the
gasket to the groove.
• As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes. Make
sure to read the instruction in this manual.
• Within five minutes of gasket application, install the mating
component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are instructions in this manual, observe them.
EMA0622D
SEM159F
PREPARATION
LU-25
< PREPARATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000001381535
Commercial Service Tools
INFOID:0000000001381536
NISSAN tool number
(RENAULT tool number)
Tool name
Description
KV113C0010
(Mot.1329)
Oil filter wrench
Removing and installing oil filter
KV113E0020
(Mot.836-05)
Oil pressure gauge set
Measuring oil pressure
Use C, E, F.
MBIB0369E
MBIB0663E
NISSAN tool number
Tool name
Description
WS39930000
Tube presser
Pressing the tube of liquid gasket
S-NT052
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст