Nissan Tiida C11. Manual — part 139
DEF-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is displayed.
-
Record DTC and freeze frame data (Print them out with CONSULT-III.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3
Symptom is described, DTC is not displayed>>GO TO 4
Symptom is not described, DTC is displayed>>GO TO 5
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT-III to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to
XX-XX, "*****"
and determine trouble diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirma-
tion Procedure.
Is DTC detected?
YES
>> GO TO 8
NO
>> Refer to
XX-XX, "*****"
.
6.
PERFORM BASIC INSPECTION
Perform
Inspection End>>GO TO 7
7.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to
based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 8
DIAGNOSIS AND REPAIR WORKFLOW
DEF-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES
>> GO TO 9
NO
>> Check voltage of related BCM terminals using CONSULT-III.
9.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it.
>> GO TO 10
10.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8
YES (Symptom remains)>>GO TO 6
NO
>> INSPECTION END
DEF-6
< FUNCTION DIAGNOSIS >
REAR WINDOW DEFOGGER SYSTEM
FUNCTION DIAGNOSIS
REAR WINDOW DEFOGGER SYSTEM
System Diagram
INFOID:0000000001697541
System Description
INFOID:0000000001697542
Operation Description
• Turn rear window defogger switch ON when the ignition switch is turned ON. Then controller (auto amp.)
(rear window defogger switch) transmits rear window defogger switch signal to BCM.
• BCM turns rear window defogger relay ON when rear window defogger switch signal is received.
• Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
• BCM transmits rear window defogger control signal to IPDM E/R via CAN communication when rear window
defogger operates.
• Rear window defogger ON is displayed when controller (auto amp.) receives signals.
Timer function
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door
mirror defogger) operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch
is turned OFF.
INPUT/OUTPUT SIGNAL CHART
*: With door mirror defogger
ALLIA0183GB
Switch
Input signal to BCM
BCM function
Acutuator
Rear window defogger switch
Defogger switch signal
Rear window defogger and door
mirror defogger
*
control
Rear window defogger
Door mirror defogger
*
Push button ignition switch
Ignition signal
REAR WINDOW DEFOGGER SYSTEM
DEF-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
Component Parts Location
INFOID:0000000001697543
Component Description
INFOID:0000000001697544
ALLIA0619ZZ
1.
BCM M18, M20 (view with glove box
removed)
2.
Rear window defogger switch (part
of front air control)
3.
A. Rear window defogger ground
connector D413 (Hatchback)
B. Rear window defogger connector
D412 (Hatchback)
C. Condenser-1 D409, D411 (Hatch-
back)
4.
A. Rear window defogger connector
B140 (Sedan)
B. Rear window defogger ground
connector B141 (Sedan)
C. Condenser-1 B130, B131 (Se-
dan)
5.
IPDM E/R E46, E48
6.
Door mirror LH D4, RH D107 (with
heated mirrors)
7.
Heated mirror relay M48 (with heat-
ed mirrors)
BCM
• Operates the rear window defogger with the operation of rear window defogger switch.
• Performs the timer control of rear window defogger.
Rear window defogger relay
• Operates the rear window defogger and the door mirror defogger with the control signal from
BCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст