Nissan Tiida C11. Manual — part 1348
SYSTEM SYMPTOM
TM-443
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK or NG
OK
>> GO TO 2.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
2.
CHECK PARKING COMPONENTS
Check parking components. Refer to
and
.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
In "N" Position, Vehicle Moves
INFOID:0000000001714349
SYMPTOM:
Vehicle moves forward or backward when selecting “N” position.
1.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 2.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
2.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Refill ATF.
3.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
-
Overrun clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Reverse clutch assembly. Refer to
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK SYMPTOM
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
SAT282F
TM-444
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Large Shock "N"
→
"R" Position
INFOID:0000000001714350
SYMPTOM:
There is a large shock when changing from “N” to “R” position.
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
TM-35, "CONSULT-III Function (TRANSMISSION)"
or
Procedure without CONSULT-III"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
.
NO
>> GO TO 2.
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 5.
5.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Does Not Creep Backward in "R" Position
INFOID:0000000001714351
SYMPTOM:
Vehicle does not creep backward when selecting “R” position.
1.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Refill ATF.
SYSTEM SYMPTOM
TM-445
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “R” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following item:
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK STALL REVOLUTION
Check stall revolution with selector lever in “1” and “R” positions. Refer to
TM-175, "Inspection and Judgment"
.
OK or NG
OK
>> GO TO 6.
OK in “1” position, NG in “R” position>>GO TO 5.
NG in both “1” and “R” positions>>GO TO 7.
5.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Low & reverse brake assembly. Refer to
.
-
Reverse clutch assembly. Refer to
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Reverse clutch assembly. Refer to
-
High clutch assembly. Refer to
.
-
Low & reverse brake assembly. Refer to
.
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
-
Overrun clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK SYMPTOM
OK or NG
TM-446
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Does Not Creep Forward in "D", "2" or "1" Position
INFOID:0000000001714352
SYMPTOM:
Vehicle does not creep forward when selecting “D”, “2” or “1” position.
1.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Refill ATF.
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following item:
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK STALL REVOLUTION
Check stall revolution with selector lever in “D” position. Refer to
TM-175, "Inspection and Judgment"
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Oil pump assembly. Refer to
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Forward one-way clutch. Refer to
TM-278, "Rear Internal Gear and Forward Clutch Hub"
.
-
Low one-way clutch. Refer to
-
Torque converter. Refer to
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст