Nissan Tiida C11. Manual — part 935
IP-22
< SERVICE INFORMATION >
INSTRUMENT PANEL ASSEMBLY
1.
Remove the instrument lower finisher.
a.
Disengage pawls and remove fuse block lid.
b.
Remove the screws.
c.
Pull backward while disengaging the instrument lower finisher
clip and pawls.
d.
Disconnect the harness connectors, and then remove instru-
ment lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER CONSOLE ASSEMBLY
Removal
1.
Insert a suitable tool into front side space of console mask, and
disengage metal clips.
2.
Disconnect harness connector, and then remove console mask.
3.
Place the selector lever in "D" position (A/T and MT only).
4.
Remove selector lever knob (A/T and MT only). Refer to
674, "Removal and Installation"
(A/T).
5.
Pull up and disengage A/T and MT console finisher metal clips
(A/T and MT only).
6.
Remove A/T and MT console finisher (A/T and MT only).
7.
Remove shift knob (M/T only). Refer to
TM-674, "Removal and Installation"
.
8.
Pull up and disengage M/T console boot metal clips (M/T only).
9.
Remove M/T console boot (M/T only).
10. Disengage console rear finisher metal clips and pawl.
11. Remove console rear finisher.
ALJIA0096ZZ
PIIB6386E
PIIB2454J
PIIB2452J
INSTRUMENT PANEL ASSEMBLY
IP-23
< SERVICE INFORMATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
12. Disengage console mask cover metal clips and pawls, and then
remove console mask cover (with armrest).
13. Disengage rear cup holder metal clips and pawls (without arm-
rest).
14. Remover rear cup holder (without armrest).
15. Remove console body assembly screws and nuts.
16. Disconnect harness connector, and then remove console body assembly.
17. Remove both of the instrument lower cover LH and RH (CS101)
clips.
18. Disengage instrument lower cover LH and RH metal clips and
remove both of the instrument lower cover LH and RH.
19. Remove the screws and then remove the center console.
Installation
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000001523319
NOTE:
The LHD model shown, RHD similar.
GLOVE BOX ASSEMBLY
PIIB6387E
PIIB6388E
PIIB2882J
IP-24
< SERVICE INFORMATION >
INSTRUMENT PANEL ASSEMBLY
Disassembly
1.
Remove screws of damper, and then remove damper.
2.
Remove screws of glove box striker, and then remove glove box striker.
3.
Remove screws of glove box latch, and then remove glove box latch.
Assembly
Assembly is in the reverse order of disassembly.
CENTER CONSOLE ASSEMBLY
1.
Glove box striker
2.
Glove box
3.
Glove box latch
4.
Damper
LIIA2555E
INSTRUMENT PANEL ASSEMBLY
IP-25
< SERVICE INFORMATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Disassembly
Remove the four screws, and then remove front cup holder from center console.
Assembly
Assembly is in the reverse order of disassembly.
COMBINATION METER
Disassembly
Disengage the eight tabs to separate front cover (1) from the unified
meter control unit assembly (2).
Assembly
Assembly is in the reverse order of disassembly.
1.
Center console
2.
Front cup holder
ALJIA0098ZZ
LIIA2582E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст