Nissan Tiida C11. Manual — part 1328
SHIFT SOLENOID VALVE A
TM-363
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK VALVE RESISTANCE
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly connector in engine room.
3.
Check resistance between terminal cord assembly harness con-
nector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK DTC
Perform
TM-361, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
XX-XX, "*****"
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000001713009
SHIFT SOLENOID VALVE A
• For removal, refer to
XX-XX, "*****"
.
Resistance Check
• Check resistance between terminal and ground.
Operation Check
Solenoid valve
Connector
Terminal
Resistance (Approx.)
Shift solenoid valve A
F30
2 - Ground
20 - 30
Ω
SCIA4942E
Solenoid valve
Terminal
Resistance (Ap-
prox.)
Shift solenoid valve A
2
Ground
20 - 30
Ω
SCIA2049E
TM-364
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE A
• Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
SCIA2052E
SHIFT SOLENOID VALVE B
TM-365
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT SOLENOID VALVE B
Description
INFOID:0000000001713010
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP
switch, vehicle speed and ECM (throttle opening). Gears will then be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001713011
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001713012
Diagnostic trouble code “SHIFT SOLENOID/V B” with CONSULT-III or 5th judgement flicker without CON-
SULT-III is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve.
Possible Cause
INFOID:0000000001713013
• Harness or connector
(Solenoid circuit is open or shorted.)
• Shift solenoid valve B
DTC Confirmation Procedure
INFOID:0000000001713014
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2.
Touch “START”.
3.
Start engine.
4.
Drive vehicle in “D” position and allow the transaxle to shift 1
→
2
→
3 (“GEAR”).
5.
If the check result is NG, go to
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle in D
1
→
D
2
→
D
3
position.
3.
Perform self-diagnosis.
Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001713016
1.
CHECK INPUT SIGNAL
With CONSULT-III
1.
Start engine.
2.
Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out the value of “SHIFT S/V B” while driving.
Check the value changes according to driving speed.
Gear position
1
2
3
4
Shift solenoid valve A
ON (Closed)
OFF (Open)
OFF (Open)
ON (Closed)
Shift solenoid valve B
ON (Closed)
ON (Closed)
OFF (Open)
OFF (Open)
Item name
Condition
Display value
SHIFT S/V B
When shift solenoid valve B operates.
(When driving in “D
1
” or “D
2
”.)
ON
When shift solenoid valve B does not operate.
(When driving in “D
3
” or “D
4
”.)
OFF
TM-366
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE B
Without CONSULT-III
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK SHIFT SOLENOID VALVE B CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 3.
3.
CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly harness connector and TCM connector.
3.
Check continuity between terminal cord assembly harness con-
nector terminal and TCM connector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
If OK, check continuity between ground and transaxle assembly.
6.
Reinstall any part removed.
OK or NG
Item name
Condition
Display value
SHIFT S/V B
When shift solenoid valve B operates.
(When driving in “D
1
” or “D
2
”.)
ON
When shift solenoid valve B does not oper-
ate.
(When driving in “D
3
” or “D
4
”.)
OFF
Item
Connec-
tor
Terminal
Condition
Judgement
standard (Ap-
prox.)
Shift sole-
noid valve B
E31
12 -
Ground
When shift solenoid
valve B operates.
(When driving in “D
1
” or
“D
2
”.)
Battery volt-
age
When shift solenoid
valve B does not oper-
ate.
(When driving in “D
3
” or
“D
4
”.)
0V
SCIA3253E
Solenoid Valve
Connector
Terminal
Resistance (Ap-
prox.)
Shift solenoid valve B
E31
12 - Ground
5 - 20
Ω
SCIA3254E
Item
Connector
Terminal
Continuity
TCM
E101
12
Yes
Terminal cord assembly
harness connector
F30
1
SCIA4943E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст