Nissan Tiida C11. Manual — part 1264
DTC TURBINE REVOLUTION SENSOR
TM-107
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Check continuity between TCM connector terminals and turbine
revolution sensor (power train revolution sensor) harness con-
nector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
Reinstall any part removed.
OK or NG
OK
>> 10A fuse (No. 49, located in the IPDM E/R) or ignition switch are malfunctioning.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK HARNESS BETWEEN TCM AND TURBINE REVOLUTION [(POWER TRAIN REVOLUTION SEN-
SOR) SENSOR GROUND]
1.
Turn ignition switch OFF.
2.
Disconnect the turbine revolution sensor (power train revolution sensor) harness connector.
3.
Check continuity between TCM connector terminal and turbine
revolution sensor (power train revolution sensor) harness con-
nector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
Reinstall any part removed.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK DTC
Perform
TM-104, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 5.
Item
Connector
Terminal
Continuity
TCM
E31
10
Yes
Turbine revolution sensor
(power train revolution sensor)
F47
1
TCM
E31
19
Yes
Turbine revolution sensor
(power train revolution sensor)
F47
1
SCIA2773E
Item
Connector
Terminal
Continuity
TCM
E32
42
Yes
Turbine revolution sensor
(power train revolution sensor)
F47
3
SCIA2774E
TM-108
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
CONTROL UNIT (RAM), CONTROL UNIT (ROM)
CONTROL UNIT (RAM), CONTROL UNIT (ROM)
Description
INFOID:0000000001694408
The TCM consists of a microcomputer and connectors for signal
input and output and for power supply. The unit controls the A/T.
On Board Diagnosis Logic
INFOID:0000000001694409
• This is not an OBD self-diagnostic item.
• Diagnostic trouble code “CONTROL UNIT (RAM)”, “CONTROL UNIT (ROM)” with CONSULT-III is detected
when TCM memory (RAM) or (ROM) is malfunctioning.
Possible Cause
INFOID:0000000001694410
TCM.
DTC Confirmation Procedure
INFOID:0000000001694411
CAUTION:
If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for A/T with CONSULT-III.
2.
Touch “START”.
3.
Start engine.
4.
Run engine for at least 2 seconds at idle speed.
5.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001694412
1.
CHECK DTC
With CONSULT-III
1.
Turn ignition switch ON and select “SELF-DIAG RESULTS” mode for A/T with CONSULT-III.
2.
Touch “ERASE”.
3.
TM-108, "DTC Confirmation Procedure"
Is the “CONTROL UNIT (RAM)” or “CONTROL UNIT (ROM)” displayed again?
YES
TM-189, "Removal and Installation"
NO
>> INSPECTION END
SAT574J
MAIN POWER SUPPLY AND GROUND CIRCUIT
TM-109
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
MAIN POWER SUPPLY AND GROUND CIRCUIT
Description
INFOID:0000000001694413
When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diag-
nosis memory function stops, malfunction is detected.
On Board Diagnosis Logic
INFOID:0000000001694414
• This is not an OBD self-diagnostic item.
• Diagnostic trouble code “INITIAL START” with CONSULT-III is detected when TCM dose not receive the
voltage signal from the battery power supply.
• This is not a malfunction message. (Whenever shutting OFF a power supply to the TCM, this message
appears on the screen.)
Possible Cause
INFOID:0000000001694415
Harness or connector
(Battery or ignition switch and TCM circuit is open or shorted.)
DTC Confirmation Procedure
INFOID:0000000001694416
CAUTION:
If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “DATA MONITOR” mode for “A/T” with CONSULT-III.
3.
Touch “START”.
4.
Wait for at least 2 consecutive seconds.
5.
If DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000001694418
1.
CHECK TCM POWER SOURCE
1.
Turn ignition switch ON. (Do not start engine.)
2.
Check voltage between TCM connector terminals and ground.
3.
Turn ignition switch OFF.
Item
Connec-
tor
Terminal
Judgement standard (Approx.)
Power supply
E31
10
Battery voltage
19
Battery voltage
Power supply
(Memory back-up)
E32
28
Battery voltage
SCIA2656E
TM-110
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
MAIN POWER SUPPLY AND GROUND CIRCUIT
4.
Check voltage between TCM connector terminals and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness for short or open between ignition switch and TCM terminals 10, 19
• Harness for short or open between battery and TCM terminal 28
• 10A fuse (No.13, located in the fuse block) and 10A fuse (No. 49, located in the IPDM E/R)
• Ignition switch.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK TCM GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between TCM connector terminals and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
4.
CHECK DTC
Perform
TM-109, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 5.
5.
CHECK TCM
1.
Check TCM input/output signal. Refer to
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Item
Connec-
tor
Terminal
Judgement standard (Approx.)
Power supply
E31
10
0V
19
0V
Power supply
(Memory back-up)
E32
28
Battery voltage
SCIA2657E
Item
Connector
Terminal
Continuity
Ground
E32
25, 48 - Ground
Yes
SCIA2671E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст