Nissan Tiida C11. Manual — part 1273
SYSTEM SYMPTOM
TM-143
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK
>> GO TO 2.
NG
>> Refill ATF.
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “R” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following item:
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK STALL REVOLUTION
Check stall revolution with selector lever in “1” and “R” positions. Refer to
TM-175, "Inspection and Judgment"
.
OK or NG
OK
>> GO TO 6.
OK in “1” position, NG in “R” position>>GO TO 5.
NG in both “1” and “R” positions>>GO TO 7.
5.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Low & reverse brake assembly. Refer to
.
-
Reverse clutch assembly. Refer to
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Reverse clutch assembly. Refer to
-
High clutch assembly. Refer to
.
-
Low & reverse brake assembly. Refer to
.
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
-
Overrun clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK SYMPTOM
TM-144
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Does Not Creep Forward in "D", "2" or "1" Position
INFOID:0000000001696248
SYMPTOM:
Vehicle does not creep forward when selecting “D”, “2” or “1” position.
1.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Refill ATF.
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following item:
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK STALL REVOLUTION
Check stall revolution with selector lever in “D” position. Refer to
TM-175, "Inspection and Judgment"
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Oil pump assembly. Refer to
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Forward one-way clutch. Refer to
TM-278, "Rear Internal Gear and Forward Clutch Hub"
.
-
Low one-way clutch. Refer to
-
Torque converter. Refer to
OK or NG
OK
>> GO TO 7.
SYSTEM SYMPTOM
TM-145
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 5.
7.
CHECK SYMPTOM
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 8.
8.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Cannot Be Started from D
1
INFOID:0000000001696249
SYMPTOM:
Vehicle cannot be started from D
1
on “Cruise Test — Part 1”.
1.
CHECK SYMPTOM
Check symptom. Refer to
.
Is “Vehicle Dose Not Creep Backward in “R” Position” OK?
OK
>> GO TO 2.
NG
>> GO TO
TM-142, "Vehicle Does Not Creep Backward in "R" Position"
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
XX-XX, "*****"
or
TM-38, "Diagnosis Procedure without CONSULT-III"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
XX-XX, "*****"
or
XX-XX, "*****"
.
NO
>> GO TO 3.
3.
CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to
(type 2).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace accelerator pedal position sensor.
4.
CHECK LINE PRESSURE
Check line pressure at stall point with selector lever in “D” position. Refer to
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve A
-
Shift valve B
TM-146
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
3.
Disassemble A/T. Refer to
4.
Check the following items:
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Low one-way clutch. Refer to
-
Forward one-way clutch. Refer to
TM-278, "Rear Internal Gear and Forward Clutch Hub"
.
-
High clutch assembly. Refer to
.
-
Torque converter. Refer to
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 5.
7.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve A
-
Shift valve B
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damage parts.
8.
CHECK SYMPTOM
Check again. Refer to
TM-183, "Cruise Test - Part 1"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
A/T Does Not Shift: D
1
→
D
2
or Does Not Kickdown: D
4
→
D
2
INFOID:0000000001696250
SYMPTOM:
A/T does not shift from D
1
to D
2
at the specified speed on “Cruise Test — Part 1”.
A/T does not shift from D
4
to D
2
when depressing accelerator pedal fully at the specified speed on
“Cruise Test — Part 2”.
1.
CHECK SYMPTOM
Check symptom. Refer to
TM-183, "Cruise Test - Part 1"
Are “Vehicle Dose Not Creep Forward in “D”, “2” or “1” Position” and “Vehicle Cannot Be Started from D
1
” OK?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст