Nissan Tiida C11. Manual — part 1341
PNP, OD SWITCH AND CLOSED THROTTLE, WIDE OPEN THROTTLE POSI-
TION SIGNAL CIRCUIT
TM-415
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK PNP SWITCH CIRCUIT
With CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out “P·N”, “R”, “D”, “2” and “1” position switches moving selector lever to each position.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 4.
3.
CHECK PNP SWITCH CIRCUIT
Without CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
2.
Check voltage between TCM connector terminals and ground
while moving selector lever through each position.
B: Battery voltage
0: 0V
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 4.
Item name
Condition
Display value
PN POSI SW
When setting selector lever to “N” or “P” posi-
tion.
ON
When setting selector lever to other positions.
OFF
R POSITION SW
When setting selector lever to “R” position.
ON
When setting selector lever to other positions.
OFF
D POSITION SW
When setting selector lever to “D” positions.
ON
When setting selector lever to other positions.
OFF
2 POSITION SW
When setting selector lever to “2” position.
ON
When setting selector lever to other positions.
OFF
1 POSITION SW
When setting selector lever to “1” position.
ON
When setting selector lever to other positions.
OFF
Selector lever position
Terminal
36
35
34
27
26
“P”, “N”
B
0
0
0
0
“R”
0
B
0
0
0
“D”
0
0
B
0
0
“2”
0
0
0
B
0
“1”
0
0
0
0
B
SCIA7162E
TM-416
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
PNP, OD SWITCH AND CLOSED THROTTLE, WIDE OPEN THROTTLE POSI-
TION SIGNAL CIRCUIT
4.
CHECK PNP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect PNP switch harness connector.
3.
Check continuity between PNP switch harness connector termi-
nals.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
CHECK CONTROL CABLE ADJUSTMENT
Check PNP switch again with control cable disconnected from manual shaft of A/T assembly. Refer to test
group 4.
OK or NG
OK
>> Adjust control cable. Refer to
XX-XX, "*****"
.
NG
>> Repair or replace PNP switch. Refer to
XX-XX, "*****"
.
6.
DETECT MALFUNCTIONING ITEM
Check the following.
• Harness for short or open between ignition switch and PNP switch
• Harness for short or open between PNP switch and TCM
• Harness for short or open between PNP switch and combination meter
• Harness for short or open between combination meter and TCM
• 10A fuse (No.51, located in the IPDM E/R)
• Combination meter.
• Ignition switch.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
7.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
With CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out “OVERDRIVE SW”. Check the signal of overdrive control switch is indicated properly.
Without CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
Selector lever position
Connector
Terminal
Continuity
“P”
F25
1 - 2, 3 - 7
Yes
*Continuity
should not
exist in posi-
tions other
than the
specified
positions.
“R”
3 - 8
“N”
1 - 2, 3 - 9
“D”
3 - 6
“2”
3 - 5
“1”
3 - 4
SCIA5588E
Item name
Overdrive control switch
Condition
Display value
OVERDRIVE SW
Depressed
ON
Released
OFF
PNP, OD SWITCH AND CLOSED THROTTLE, WIDE OPEN THROTTLE POSI-
TION SIGNAL CIRCUIT
TM-417
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 8.
8.
CHECK OVERDRIVE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect A/T device harness connector.
3.
Check continuity between A/T device harness connector termi-
nals.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
9.
DETECT MALFUNCTIONING ITEM
Check the following.
• Harness for short or open between combination meter and A/T device harness connector
• Harness for short or open between A/T device harness connector and ground
• Combination meter.
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK CLOSED THROTTLE POSITION AND WIDE OPEN THROTTLE POSITION SIGNAL CIRCUIT
With CONSULT-III
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for TRANSMISSION with CONSULT-III.
3.
Read out “CLOSED THL/SW” and “W/O THRL/P-SW” depressing and releasing accelerator pedal.
Check that the signals of throttle position are indicated properly.
OK or NG
OK
>> GO TO 11.
NG
>>
Check the following. If any items are damaged, repair or replace damaged parts.
• Accelerator pedal position sensor. Refer to
XX-XX, "*****"
.
Item
Connector
Terminal
Overdrive
control switch
Condition
Judge-
ment
standard
(Approx.)
A/T device harness
connector (Overdrive
control switch)
M38
1 - Ground
Released
Battery
voltage
Depressed
0V
SCIA5336E
Item
Connector
Terminal
Overdrive control
switch condition
Continuity
A/T device harness con-
nector (Overdrive con-
trol switch)
M38
1 - 2
Released
No
Depressed
Yes
SCIA5330E
Accelerator pedal condition
Data monitor
CLOSED THL/SW
W/O THRL/P-SW
Released
ON
OFF
Fully depressed
OFF
ON
TM-418
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
PNP, OD SWITCH AND CLOSED THROTTLE, WIDE OPEN THROTTLE POSI-
TION SIGNAL CIRCUIT
11.
PERFORM SELF-DIAGNOSIS
Without CONSULT-III
Perform self-diagnosis. Refer to
XX-XX, "*****"
.
OK or NG
OK
>> INSPECTION END
NG
−
1 >> Self-diagnosis does not activate: GO TO 12.
NG
−
2 >> DTC is displayed: Check the malfunctioning system. Refer to
XX-XX, "*****"
.
12.
CHECK TCM
1.
Check TCM input/output signal. Refer to
XX-XX, "*****"
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000001713110
OVERDRIVE CONTROL SWITCH
• Check continuity between A/T device harness connector terminals.
PNP SWITCH
1.
Check continuity between PNP switch harness connector termi-
nals.
2.
If NG, check again with control cable (2) disconnected from
manual shaft of A/T assembly. Refer to step 1.
(1): Lock nut
(3): Manual shaft
3.
If OK on step 2, adjust control cable (2). Refer to
XX-XX, "*****"
.
4.
If NG on step 2, remove PNP switch from A/T assembly and
check continuity of PNP switch terminals. Refer to step 1.
5.
If OK on step 4, adjust PNP switch. Refer to
XX-XX, "*****"
.
6.
If NG on step 4, replace PNP switch. Refer to
XX-XX, "*****"
.
Item
Connector
Terminal
Overdrive control
switch condition
Continuity
A/T device harness con-
nector (Overdrive con-
trol switch)
M38
1 - 2
Released
No
Depressed
Yes
SCIA5330E
Selector lever position
Connector
Terminal
Continuity
“P”
F25
1 - 2, 3 - 7
Yes
*Continuity
should not
exist in posi-
tions other
than the
specified
positions.
“R”
3 - 8
“N”
1 - 2, 3 - 9
“D”
3 - 6
“2”
3 - 5
“1”
3 - 4
SCIA5588E
SCIA6370J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст