Nissan Tiida C11. Manual — part 1302
REPAIR FOR COMPONENT PARTS
TM-259
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Check operation of reverse clutch
a.
Install seal rings to drum support of oil pump assembly, and set
reverse clutch assembly.
b.
Apply compressed air into the oil hole at the location as shown.
c.
Check to see that retaining plate moves to snap ring.
d.
If retaining plate does not contact snap ring:
• D-ring might be damaged.
• Seal ring might be damaged.
• Fluid might be leaking past piston check ball.
2.
Remove snap ring (1) using suitable tool (A).
3.
Remove retaining plate, drive plates, driven plates and dish
plates.
4.
Set Tool on spring retainer assembly, and remove snap ring
from reverse clutch drum while compressing spring retainer
assembly.
CAUTION:
Set Tool directly over return springs.
5.
Remove spring retainer assembly from reverse clutch drum.
CAUTION:
Do not remove return springs from spring retainer.
6.
Install seal rings to drum support of oil pump assembly (1), and
set reverse clutch drum (2). Then apply compressed air into the
oil hole at the location as shown to remove reverse clutch piston
(3) from reverse clutch drum (2).
CAUTION:
Do not flow air in too quickly or reverse clutch piston (3)
and ATF could jump out. Carefully flow air in little by little
while protecting with lint-free cloth.
7.
Remove D-ring (1) and seal ring (2) from reverse clutch piston
(3).
SAT155D
SCIA7024J
SAT157D
SCIA5999J
SCIA5998J
TM-260
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
INSPECTION
Reverse Clutch Snap Ring
Check for deformation, fatigue or damage. Replace if necessary.
Reverse Clutch Drive Plates
• Check facing for burns, cracks or damage. Replace if necessary.
• Measure thickness of facing.
CAUTION:
• Measure the thickness at 3 locations and find the average.
• Inspect ALL drive plates.
• Replace if the thickness is below the allowable limit.
Reverse Clutch Dish Plates
• Check for deformation or damage.
• Measure thickness (t) of dish plate. Replace if damaged, deformed
or worn.
Reverse Clutch Spring Retainer Assembly
Measure length (L) of spring retainer assembly. Replace if damaged,
deformed or worn.
CAUTION:
Do not remove return springs (A) from spring retainer (B)
Reverse Clutch Piston
• Make sure that check balls do not stick.
• Apply compressed air to check ball oil hole opposite from return
spring. Make sure there is no air leakage.
• Apply compressed air to oil hole on return spring side to make sure
that air leaks past ball.
Reverse Clutch Drum
Check for deformation or damage. Replace if necessary.
ASSEMBLY
Thickness of drive plate
Standard and allowable limit:
.
SAT162D
Thickness of dish plate (t):
2.87 mm (0.1130 in)
SAT163D
Length (L):
20.1 mm (0.791 in)
SCIA7025J
SAT164D
REPAIR FOR COMPONENT PARTS
TM-261
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Install D-ring (1) and seal ring (2) on reverse clutch piston (3).
CAUTION:
Be careful with the direction of seal ring (2).
2.
Install reverse clutch piston by turning it slowly.
CAUTION:
Apply ATF to inner surface of reverse clutch drum.
3.
Install spring retainer assembly (1) to reverse clutch piston (2).
4.
Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
Set Tool directly over return springs.
5.
Install dish plates (5), driven plates (4), drive plates (3) and
retaining plate (2).
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Dish plate
Drive plate/Driven plate: 2/2
CAUTION:
Be careful with the order of plates.
SCIA5998J
SAT159D
SCIA6000J
SAT157D
SCIA7003J
TM-262
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
NOTE:
Install two dish plates fitting each installation direction with
reverse clutch drum groove displaced slightly.
6.
Install snap ring (1) using suitable tool (A).
7.
Measure clearance between retaining plate and snap ring using
feeler gauge. If not within allowable limit, select proper retaining
plate.
8.
Check operation of reverse clutch. Refer to
.
High Clutch
INFOID:0000000001730989
COMPONENTS
SAT170D
SCIA7024J
Specified clearance
Standard and allowable limit:
.
SAT174D
SCIA6741E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст