Nissan Tiida C11. Manual — part 1394
PREPARATION
TM-627
< PREPARATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Commercial Service Tools
INFOID:0000000001381680
Tool name
Description
Drift
a: 38 mm (1.50 in) dia.
• Removing input shaft oil seal
• Removing input shaft front bearing
Drift
a: 14.5 mm (0.571 in) dia.
Installing bushing
S-NT063
S-NT063
TM-628
< ON-VEHICLE MAINTENANCE >
[5MT: RS5F91R]
GEAR OIL
ON-VEHICLE MAINTENANCE
GEAR OIL
Exploded View
INFOID:0000000001381681
Draining
INFOID:0000000001381682
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and drain oil.
3.
Set a new gasket on drain plug (1) and install it to transaxle and
tighten drain plug to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000001381683
1.
Remove filler plug (1). Fill with new oil until oil level reaches the
specified limit near filler plug hole as shown.
2.
After refilling oil, check oil level.
3.
Set a new gasket on filler plug (1), then install it to transaxle and
tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
Inspection
INFOID:0000000001381684
LEAKAGE
Make sure that oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Do not start engine while checking oil level.
2.
Set a new gasket on filler plug (1) and install it to the transaxle
case.
CAUTION:
Do not reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
PCIB1504E
Oil grade and capacity
: Refer to
SCIA7119E
SCIA7119E
SIDE OIL SEAL
TM-629
< ON-VEHICLE REPAIR >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded View
INFOID:0000000001381685
Removal and Installation
INFOID:0000000001381686
REMOVAL
1.
Remove front drive shafts from transaxle assembly. Refer to XX-XX, "*****".
2.
Remove differential side oil seal (1) using suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
•
⇐
: Front
• Install new differential side oil seal (1) to clutch housing and tran-
saxle case using Tool (A).
CAUTION:
• Do not reuse differential side oil seal.
• When installing, do not incline differential side oil seal.
• Do not damage clutch housing or transaxle case.
• Check oil level after installation. Refer to
.
PCIB1505E
Tool number
: ST27862000 (
—
)
Dimension “H
1
”
: 5.7 - 6.3 mm (0.224 - 0.248 in)
Dimension “H
2
”
: 16.4 - 17.0 mm (0.646 - 0.669 in)
PCIB1506E
TM-630
< ON-VEHICLE REPAIR >
[5MT: RS5F91R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded View
INFOID:0000000001381687
Removal and Installation
INFOID:0000000001381688
REMOVAL
1.
Remove battery. Refer to
PG-6, "Removal and Installation"
2.
Remove air duct (Inlet), air duct and air cleaner case. Refer to
EM-27, "Removal and Installation"
.
3.
Press the release button (1) of select cable and shift cable, and
then remove select cable and shift cable from lever of control
shaft (2).
4.
Shift control lever to neutral position.
5.
Remove control lever knob.
6.
Remove center console assembly. Refer to
.
7.
Remove control device assembly mounting bolts.
8.
Remove exhaust front tube, center muffler and heat plate. Refer
to
EX-5, "Removal and Installation"
9.
Remove bracket.
10. Remove select cable and shift cable from cable mounting bracket.
11. Remove control device assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
1.
Control lever knob
2.
Control lever
3.
Control device assembly
4.
Select cable
5.
Shift cable
6.
Clutch housing
7.
Cable mounting bracket
8.
Bracket
A: Black
color
B: White
color
PCIB1508E
SCIA7077E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст